JVC TK-C2301WPRU Instruction Manual - Page 32

Refer to Mounting the Camera Using the Conduit Hole at

Get JVC TK-C2301WPRU PDF manuals and user guides View all JVC TK-C2301WPRU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Installation Mounting the Camera (Continued) Mounting the Camera Using the Conduit Hole at the Side of the Base If the camera cannot be mounted directly to the ceiling, use the conduit hole at the side of the base to mount the camera to the pipe. Conduit hole: G3/4-14 UNC (TK-C2301WPRU), M25 (TK-C2301WPRE) 1 Remove the dome cover and inner dome (A page 23) 2 Remove the camera unit from the base and mount the fall prevention wire to the camera unit Refer to "Mounting the Camera Using the Conduit Hole at the Bottom of the Base" (A page 30) step 2. 3 Wind the sealing tape Wind the sealing tape around the pipe junction (where the conduit hole thread lines with the pipe screw hole) two or more times. 4 Remove the conduit plug from the base Loosen the mounting screw (M3 x 6 mm) using a flathead screwdriver and remove the conduit plug at the side of the base. 5 Mount the conduit plug that was removed to the conduit hole at the bottom of the base 6 Mount the base to the pipe Screw the pipe to the conduit hole at the side of the base. Note When screwing the pipe, do not screw beyond 12 mm. Doing so can damage the camera interior. Conduit plug 3 4 Sealing tape 5 . 6 Mounting screw 7 Refer to "Mounting the Camera Using the Conduit Hole at the Bottom of the Base" (A page 30) step 6 to 9 E-32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Mounting the Camera (Continued)
Mounting the Camera Using the Conduit Hole at the Side of the
Base
If the camera cannot be mounted directly to the ceiling, use the conduit
hole at the side of the base to mount the camera to the pipe.
Conduit hole: G3/4-14 UNC (TK-C2301WPRU), M25 (TK-C2301WPRE)
1
Remove the dome cover and inner dome (
A
page 23)
2
Remove the camera unit from the base and mount the fall
prevention wire to the camera unit
Refer to "Mounting the Camera Using the Conduit Hole at the Bottom of
the Base" (
A
page 30) step 2.
3
Wind the sealing tape
Wind the sealing tape around the pipe junction (where the conduit hole
thread lines with the pipe screw hole) two or more times.
4
Remove the conduit plug from the base
Loosen the mounting screw (M3 x 6 mm) using a flathead screwdriver
and remove the conduit plug at the side of the base.
5
Mount the conduit plug that was removed to the conduit hole at
the bottom of the base
6
Mount the base to the pipe
Screw the pipe to the conduit hole at the side of the base.
Note
When screwing the pipe, do not screw beyond 12 mm. Doing
so can damage the camera interior.
4
5
6
3
Sealing tape
Mounting screw
Conduit plug
7
Refer to "Mounting the Camera Using the Conduit Hole at the
Bottom of the Base" (
A
page 30) step 6 to 9
Installation
E-32