JVC TKC215V12U Instructions - Page 11

Installation and connection (continued) Mounting the Camera to the Ceiling (continued) When mounting the camera directly to the ceiling or on the wall When mounting to a wall, replace areas indicated as "ceiling" in the procedures by "wall". Ⅵ Setup 1. Open a hole in the ceiling. (R30 mm) Make use of the template supplied to open a hole. 2. Draw the fall prevention wire mounted to the ceiling slab and the cable out from the ceiling in advance. CAUTION: ● Select a suitable safety cable based on length, strength, location, material (insulation property), etc. ● Use a ring on the fall prevention wire for mounting to the camera unit with an internal diameter of at least R3.1 mm or and not larger than R5.5 mm, and an external diameter that is not larger than R 9 mm. 3. Remove the dome cover. As illustrated in the diagram, hold the dome ring such that the position mark comes between the thumb and index finger. Turn the ring in the anti-clockwise direction to remove. 3. Dome Ring Position mark 4. Remove the outer case. A Loosen the camera fastening screw with a screwdriver. B To remove, turn the camera unit in the anti- clockwise direction. C Dismantle the fall prevention wire. 5. Loosen the pan fastening screw. CAUTION: ● Moving the lens unit without loosening the pan fastening screw may damage the lens unit. 6. Set the switches for video images. (TK-C215V4 A pg. 10) (TK-C215V12 A pg. 12) (TK-C210FW A pg. 14) 5. 4. Pan fastening Screw 6. A Camera Fastening Screw C 4. B *TK-C215V4 is used in the above illustration Ⅵ Connecting 1. Align j with the shooting direction when mounting the cover to the ceiling. Mount by using the supplied adapter ring to clamp between the outer case and the ceiling. Notes on outer case mounting screws (not supplied): ● The diameter of the attachment hole of outer case is R4.5 mm (3/16 inch). ● Do not use flathead screws. ● When using an impact screwdriver, do not tighten the screws fully. Tighten using your hand instead. Failure to do so may damage the outer case. 2. Hang the fall prevention wire that has been dismantled in Step 4 C of the setup procedures to the hook. 3. Attach the fall prevention wire to the camera. (Fall prevention wire is not included) CAUTION: ● Tighten all screws securely. Otherwise the camera may come loose and fall. 20 Installation and connection (continued) Adaptor ring 1. Fall prevention wire (not supplied) UPFRONT Attach from the ceiling slab 3. 2. Be sure to loosen the screw. *TK-C215V4 is used in the above illustration 4. Connect the video signal cable. (A pg. 14) Lower the protection cover and connect the connectors. Upon connecting, restore the protection cover to cover the connectors. 5. Connect the input power supply cable. (A pg. 15) 6. Install the Ferrite core (TK-C210FW only) (A pg. 14) 7. Connect the alarm cable. (TK-C215V12 only) (A pg. 15) 8. Wrap insulation tape around cables. Ⅵ Mounting 1. Align the position mark of the fastened outer case with that of the camera unit. NOTE: When doing so, be careful not to catch the cables in the outer case. 2. Turn the camera unit in the clockwise direction. T When doing so, ensure that the X mark is visible. (See illustration below) 3. Fasten the camera by tightening the camera fastening screw. Position mark 1. 2. T Check Camera fastening screw 3. *TK-C215V4 is used in the above illustration Alarm signal cable (TK-C215V12 only) 5.7. 4. Solder or crimp Ⅵ Adjusting Images After mounting is completed, adjust the images while checking the actual image. (A pg. 23 AAdjusting ImagesB) Protection cover Insulation tape Wrap with tape 8. Input power supply cable *TK-C215V12 is used in the above illustration 21