Kenmore 7975 Use and Care Guide - Page 12

Acaution

Get Kenmore 7975 - Elite 25.0 cu. Ft. Trio Ice PDF manuals and user guides View all Kenmore 7975 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Reinstalling the Refrigerator Door I_ Right Door 1. Lower the door onto middle hinge pin (9). 2. Fit top hinge (5) over hinge lever latch (6) and into place. Rotate lever (4) counterclockwise to secure hinge. 3. Connect wire harnesses (3). 4. Hook tab on switch side of coner under edge of wire opening in cabinet top. Position cover (2) into place. Insert and tighten cover screw (1). (1).......... (2) Left Door 1. Lower the door onto middle hinge pin (10). 2. Fit top hinge (7) over hinge lever latch (8) and into place. Rotate lever (6) clockwise to secure hinge. 3. Install the grounding screw (5) and connect the three wire harnesses (4). 4. Push the water supply tube into the hole on the top case and pull it out on the backplate. 5. Insert the water supply tube (3) into the connector tube until you see only one scale mark. (Fully insert the tube over 5/8" (15 mm)). 6. Hook tab on door switch side of cover (2) under edge of wire opening in cabinet top. Position cover into place. Insert and tighten cover screw (1). _2J _ (3) _ (2) _1) (3). / (8) A CAUTION Collet Tube Insert Line Clip I 12 After inserting, pull the tube to make sure that it is secure and reinsert the clip.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
Reinstalling
the Refrigerator
Door
I_ Right Door
1. Lower the door onto middle
hinge pin (9).
2. Fit top hinge (5) over hinge lever latch (6) and into place.
Rotate lever (4) counterclockwise
to secure hinge.
3. Connect wire harnesses
(3).
4. Hook tab on switch side of coner under edge of wire
opening
in cabinet top. Position cover (2) into place.
Insert and tighten cover screw (1).
(1)
..........
_2J
_
(3)
_
(2)
Left Door
1. Lower the door onto middle
hinge pin (10).
2. Fit top hinge (7) over hinge lever latch (8) and into place.
Rotate lever (6) clockwise
to secure hinge.
3. Install the grounding
screw (5) and connect the three
wire harnesses
(4).
4. Push the water supply tube into the hole on the top case
and pull it out on the backplate.
5. Insert the water supply tube (3) into the connector
tube
until you see only one scale mark. (Fully insert the tube
over 5/8" (15 mm)).
6. Hook tab on door switch side of cover (2) under edge of
wire opening
in cabinet top. Position cover into place.
Insert and tighten cover screw (1).
(2)
_1)
(3).
/
(8)
A
CAUTION
Collet
Tube
Insert Line
Clip
I
After inserting, pull the tube to
make sure that it is secure and
reinsert the clip.
12