Kenmore 7975 Use and Care Guide - Page 31

Connect, The Tubing, To The, Refrigerator, Water, On At The, Sh Utoff, Valve, In The, Start,

Get Kenmore 7975 - Elite 25.0 cu. Ft. Trio Ice PDF manuals and user guides View all Kenmore 7975 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

9. CONNECT THE TUBING TO THE REFRIGERATOR NOTE: • Before making the connection to the refrigerator, be sure the refrigerator power cord is not plugged into the wall outlet. 1. Remove the plastic flexible cap from the water valve. 2. Place the compression nut and ferrule (sleeve) onto the end of the tubing as shown. 3. Insert the end of the copper tubing into the connection as far as possible. While holding the tubing, tighten the fitting. _, CAUTION: Check to see if leaks occurs at water line connections. 1/4 "Tubing 10. TURN THE WATER ON AT THE SH UTOFF VALVE Tighten any connections that leak. Reattach the compressor compartment access cover. 11. PLUG IN THE REFRIGERATOR Arrange the coil of tubing so that it does not vibrate against the back of the refrigerator or against the wall. Push the refrigerator back to the wall. Compression _ _\ Ferrule_ (sleeve) _ t___ _ Ceofnringercattioorn _, CAUTION: Check to see if water dripping occurs at water line connections. 12. START THE ICEMAKER Set the icemaker power switch to the ON position. The icemaker will not begin to operate until it reaches its operating temperature of 15°F (-9°C) or below. It will then begin operation automatically if the icemaker power switch is in the I (on) position. 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
9. CONNECT
THE TUBING
TO THE
REFRIGERATOR
NOTE:
•
Before making the connection
to the refrigerator,
be
sure the refrigerator
power cord is not plugged
into
the wall outlet.
1. Remove the plastic flexible cap from the water valve.
2. Place the compression
nut and ferrule
(sleeve) onto
the end of the tubing as shown.
3. Insert the end of the copper tubing into the
connection
as far as possible. While holding the
tubing, tighten the fitting.
_, CAUTION:
Check to see if leaks occurs at water line
connections.
Compression
_
_\
Ferrule
_
_
(sleeve)
t___
_
efrigerator
Connection
1/4
"Tubing
10. TURN
THE
WATER
ON AT THE
SH UTOFF
VALVE
Tighten any connections
that leak.
Reattach the compressor
compartment
access cover.
11. PLUG
IN THE
REFRIGERATOR
Arrange the coil of tubing so that it does not vibrate
against the back of the refrigerator
or against the
wall. Push the refrigerator
back to the wall.
_,
CAUTION:
Check to see if water dripping occurs
at
water line connections.
12. START
THE
ICEMAKER
Set the icemaker
power switch to the ON position.
The icemaker
will not begin to operate until it reaches
its operating
temperature
of 15°F (-9°C)
or below.
It
will then begin operation
automatically
if the
icemaker
power switch is in the I (on) position.
31