Kenmore 9791 Installation Instructions - Page 9

Electrical, For A 3- Wire, System, For A 4- Wire

Page 9 highlights

ELECTRICAL CONNECTIONS FOR A 3- WIRE SYSTEM ELECTRICAL CONNECTIONS FOR A 4- WIRE SYSTEM NO!V-CANAD/AN ELECTR/CLaundry Center 1. Remove the screw securing the terminal block access cover to the rear panel and remove cover. 2. Install a U.L approved strain relief connector in the entry hole on the back panel. 3. Insert a NEMA 10-30 Type SRDT, U.L approved power cord through the strain relief. 4. Attach the power cord neutral (central wire) conductor to the silver colored center terminal on the terminal block. Tighten the screw securely. GREEN GROUND SCREW SILVER TERMINAL !VON-CANAD/AN ELECTR/CLaundry Center 1. Remove the screw securing the terminal block access cover to the rear panel and remove cover. . Install a U.L approved strain relief connector in the entry hole on the back panel. . Remove the neutral ground wire from the green ground screw located above the termial block. GREEN GROUND GREEN SCREW CONDUCTOR SILVER TERMINAL TERMINAL BLOCK NEUTRAL GROUND WIRE NEUTRAL GROUND WIRE BLACK WHITE , Attach the remaining two power cord outer conductors to the outer brass colored terminals on the terminal block. Tighten both screws securely. , Tighten the screws securing the cord restraint against the power cord. 7. Reinstall the terminal access cover. STRAIN " RELIEF MOUNTING BRACKET, POWER CORD . Insert a NEMA 14-30 Type STor SRDT,U.L approved power cord through the strain relief. . Attach the green power cord ground wire to the cabinet with the green ground screw. . Attach the white (neutral) wire from the power cord and the neutral ground wire from the appliance harness to the silver colored center terminal on the terminal block. Tighten the screw securely. . Attach the red and black wires from the power cord to the outer brass-colored terminals on the terminal block. Tighten both screws securely. . Tighten the screws securing the cord restraint firmly against the power cord. 9. Reinstall the terminal block access cover. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20

ELECTRICAL
CONNECTIONS
FOR A 3- WIRE
SYSTEM
NO!V-CANAD/AN
ELECTR/C
Laundry
Center
1. Remove the screw securing the
terminal
block access cover to
the rear panel and remove cover.
2.
Install a U.L approved strain
relief connector in the entry
hole on the back panel.
3.
Insert a NEMA 10-30 Type SRDT,
U.L approved power cord through the strain relief.
4. Attach the power cord neutral (central wire) conductor
to
the silver colored center terminal on the terminal
block.
Tighten the screw securely.
GREEN
GROUND
SCREW
SILVER TERMINAL
ELECTRICAL
CONNECTIONS
FOR A 4- WIRE
SYSTEM
!VON-CANAD/AN
ELECTR/CLaundry
Center
1. Remove the screw securing the
terminal
block access cover to the
rear panel and remove cover.
.
.
Install a U.L approved strain relief
connector in the entry hole on the
back panel.
Remove the
neutral ground
wire from the green ground
screw located above the termial block.
GREEN
GROUND
GREEN
SCREW
CONDUCTOR
SILVER
TERMINAL
TERMINAL
BLOCK
NEUTRAL
GROUND
WIRE
NEUTRAL
GROUND
WIRE
BLACK
WHITE
,
,
Attach the remaining two power cord outer conductors to
the outer brass colored terminals on the terminal
block.
Tighten both screws securely.
Tighten the screws securing the cord restraint against the
power cord.
7.
Reinstall the terminal access cover.
STRAIN
"
RELIEF
MOUNTING
BRACKET,
.
POWER
CORD
Insert a NEMA 14-30 Type STor SRDT,U.L approved power
cord through the strain relief.
.
.
.
.
Attach
the green power
cord ground
wire to the cabinet
with the green ground screw.
Attach the white (neutral) wire from the power cord and the
neutral ground wire from the appliance harness to the silver
colored center terminal
on the terminal block. Tighten the
screw securely.
Attach the red and black wires from the power cord to the
outer brass-colored terminals on the terminal block. Tighten
both screws securely.
Tighten the screws securing the cord restraint firmly against
the power cord.
9.
Reinstall the terminal block access cover.
9