Kenwood DDX814 Instruction Manual

Kenwood DDX814 - EXCELON DOUBLE DIN DVD RECEIVER Manual

Get Kenwood DDX814 - EXCELON DOUBLE DIN DVD RECEIVER PDF manuals and user guides
UPC - 019048183385
View all Kenwood DDX814 manuals
Add to My Manuals
Save this manual to your list of manuals

Kenwood DDX814 manual content summary:

  • Kenwood DDX814 | Instruction Manual - Page 1
    the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new GPS Navigation System/DVD Receiver. For your records Record the serial number, found on the back of the unit, in the spaces designated on
  • Kenwood DDX814 | Instruction Manual - Page 2
    40 Channel Memory 40 Direct Channel Search 41 HD Radio Control (North American sales area only) 42 Source Control Screen 42 Auto Memory 43 Manual Memory 43 Receive mode 44 Direct Search 44 iTunes Tagging (HD Radio Tagging) 45 Bluetooth Audio Control 46 Before Use 46 Source
  • Kenwood DDX814 | Instruction Manual - Page 3
    Unit PIN Code 77 Bluetooth Unit Connection 77 AV Input Setup 78 AV Interface Setup 78 Navigation Setup 79 DSP Bypass Control 80 Speaker Setup 80 Car Type (DTA) Setup 82 Channel Level 83 DVD Setup 84 DVD Language Setup 84 DVD Parental Level Setup 85 Disc Setup 86 USB
  • Kenwood DDX814 | Instruction Manual - Page 4
    to the next page The instruction continues to the next page. Make sure to flip the page for the rest of the instruction. 4 DNX9140/DDX814/DDX8034BT [CRSC] FM Turns memory one after another. "MANU" Switches to the next frequency manually. 2 sec. Continue to touch until the memory number appears.
  • Kenwood DDX814 | Instruction Manual - Page 5
    of DVD-VIDEO playback. -VR : Function of DVD-VR playback. oCD : Function of Video CD playback media. : Function of USB device. : Function of FM reception. : Function of SIRIUS source. : Function of XM source. Press 2 seconds injuries etc. Special instructions, supplementary explanations, limitations
  • Kenwood DDX814 | Instruction Manual - Page 6
    to your writing software, and your recorder instruction manual.) • If you try to load a 3-inch-disc with its adapter into the unit, the adapter might separate from the disc and damage the unit. Other notes • If you experience problems during installation, consult your Kenwood dealer. • When you
  • Kenwood DDX814 | Instruction Manual - Page 7
    layer) DVD+R DL (Double layer) ‡ ‡ Only video format DVD-RAM × CD Music CD ‡ CD-TEXT/8-cm (3 inch) discs supported. CD-ROM ‡ MP3/ partly possible. × : Playback is impossible. ⁄ • When buying DRM enabled contents, check the Registration Code in the (page 67). Registration Code
  • Kenwood DDX814 | Instruction Manual - Page 8
    this unit (DDX814/ DDX8034BT only) • KNA-G510*/ G431* • KNA-DV4100 • KNA-DV3100 • KNA-DV2100 * Update the navigation software to the latest version. For how to update the software, refer to the instruction manual of the navigation unit. About Satellite Radio tuner This unit supports Satellite
  • Kenwood DDX814 | Instruction Manual - Page 9
    DVD players are given a region code according to the country or the type of screen for the image. The left mark 16:9 LB indicates that a wide image picture (16:9) is displayed on manual. Prohibition Mark Discs with limited period of use Do not leave discs with a limited period of use in this unit
  • Kenwood DDX814 | Instruction Manual - Page 10
    NAV SRC TEL ABC Reset button (page 6) SI indicator (page 70) D E FG Remote control sensor 1 sec. : Press for more than 1 second A Attenuation of the volume On/Off. 1 sec. Keep the tag data of the currently listening music of HD Radio. t B Volume adjustment. C Displays Graphic Equalizer
  • Kenwood DDX814 | Instruction Manual - Page 11
    DDX814/ DDX8034BT Hands Free control screen On/Off. 1 sec. 7 While watching the playback screen of a visual source or the navigation screen Displays the Easy Control CAM image and source image. NAV 1 sec. Screen Switching Function Switching between the navigation screen and the source control screen
  • Kenwood DDX814 | Instruction Manual - Page 12
    and use the navigation function, see the Navigation Instruction Manual. ⁄ • For DDX814/ DDX8034BT, an optional navigation system needs to be connected. See (page 8) for connectable navigation units. 12 DNX9140/DDX814/DDX8034BT The Source Select
  • Kenwood DDX814 | Instruction Manual - Page 13
    , refer to the instruction manual of the navigation system. 0 Press the [0] button to open/close the front panel. If a disc is already inserted, it is ejected by pressing the [0] button. 7 iPod To disconnect the iPod, stop the playback by touching the [38] button on the source control screen, and
  • Kenwood DDX814 | Instruction Manual - Page 14
    While watching the navigation screen The Source Control screen appears. DNX9140/DDX814/ DDX8034BT While watching the Easy Control screen TEL 1 sec. The Source Control screen appears. ⁄ • The screen will return to the navigation screen by touching the same part of the Source Control screen. 14
  • Kenwood DDX814 | Instruction Manual - Page 15
    Top Menu screen [NAV ] Switches to the navigation screen. [SRC ] Switches to the source control screen of the selected source. [TEL ] Switches to the Hands Free Main screen. (page 52) [NAV SETUP] Displays Navigation SETUP screen. (Instruction manual of the Navigation part) (DNX9140 only) [SRC
  • Kenwood DDX814 | Instruction Manual - Page 16
    Reverse search. 2 Displays Menu control screen (DVD-VIDEO, DVD-VR source), Picture control buttons (sources with picture files), or Zoom control buttons (Video CD). Switches TV band. 3 4 ⁄ • The information display is cleared automatically after approximately 5 seconds. 16 DNX9140/DDX814/DDX8034BT
  • Kenwood DDX814 | Instruction Manual - Page 17
    [¢], [7], [£8] Buttons for source control. The buttons are different depending on the source. See the operation pages of each source. While watching the visual source TEL 1 sec. The Easy control screen appears. ⁄ • Easy Control screen is hidden when you touch the central part of the monitor. Basic
  • Kenwood DDX814 | Instruction Manual - Page 18
    [38] Plays or pauses. Source Control Screen Switches to the source control screen to use various playback functions. 1 Display the Source Control Screen See (page 14). 2 Operation on the Source Control Screen DVD-VIDEO/DVD-VR 1 18 DNX9140/DDX814/DDX8034BT
  • Kenwood DDX814 | Instruction Manual - Page 19
    the [TIME] to change play time display. [ ] When appears, the text display is scrolled by touching it. [ ] Closes the multi function bar. DVD-VIDEO [REP] Switches the Repeat Play operations in the following sequence. Title Repeat, Chapter Repeat, Repeat Off [TIME] Switches the play time display in
  • Kenwood DDX814 | Instruction Manual - Page 20
    Disc Menu Selects an option from the DVD-VIDEO Disc Menu. 1 Display the Playback Screen See (page 16). 2 Display the Menu Control 1 screen 3 Operation on the Menu Control 1 screen ⁄ • Touching the central part of the monitor also turns on the
  • Kenwood DDX814 | Instruction Manual - Page 21
    [Zoom] Changes the zoom ratio at 4 levels (2 times, 3 times, 4 times, or off ) each time you touch. [2], [3], [5], [∞] Scrolls the screen in the direction you touch. [Return] Returns to the previous screen. [Exit] Exits the Zoom Control screen. Video CD Zoom Control Displays an enlarged VCD screen
  • Kenwood DDX814 | Instruction Manual - Page 22
    for playable discs. • See (page 7), (page 7) or (page 8) for playable files. Source Control Screen Switches to the source control screen to use various playback functions. 1 Display the Source Control Screen See
  • Kenwood DDX814 | Instruction Manual - Page 23
    the top hierarchy level. [ UP] Moves up a hierarchy level. [ TOP] USB Moves to the top folder. [ CUR] Displays the currently playing folder. [CTRL] Returns to the Source Control screen. Play list AudioFile in USB List Select Folder list: Searches folders and Audio/ Video/ Picture files stored
  • Kenwood DDX814 | Instruction Manual - Page 24
    Audio File Listening & Video File/ Picture File Watching Scrolls to the position of the specified initial USB device select Selects the connected USB device (or a partition). 1 Display the Source Control Screen See (page 22). 2 Display the USB Device Select Screen Scrolls
  • Kenwood DDX814 | Instruction Manual - Page 25
    Link search (Audio file in USB) Searches for another song of the currently selected artist. 1 Display the Source Control Screen See (page 22). 2 Returns to the Source Control screen. Scrolls to the position of the specified initial Playback Screen (Video file, Picture file)
  • Kenwood DDX814 | Instruction Manual - Page 26
    page 16). 2 Display the Menu Control screen Picture Control Adjusting the video display. 1 Display the Playback Control Screen 3 Operation on the Menu Control screen [SUB] Switches the subtitle language. [Audio] Switches the voice language. [Exit] Exits the Menu Control screen. 26 DNX9140/DDX814
  • Kenwood DDX814 | Instruction Manual - Page 27
    iPod Control You can control and listen to songs in your iPod by connecting an iPod to this unit with KCA-iP301V (optional accessory). You can also display video contents on this unit when connecting an iPod with video. Playback Screen Basic functions are available even when the playback screen is
  • Kenwood DDX814 | Instruction Manual - Page 28
    . iPod List Lists and searches music/video contained in the iPod. 1 Display the Source Control Screen See (page 28). 2 Display the iPod List 3 Select music/video 1 1 Categories and music are listed. Touch a category name to move to its lower level. If music title is displayed
  • Kenwood DDX814 | Instruction Manual - Page 29
    the specified initial Link search (Music file) Searches for another song of the currently selected artist. 1 Display the Source Control Screen See (page 28). 2 Start Link search Scrolls to the selected initial. 3 Select a song 1 1 Plays the touched song. [ ] When appears
  • Kenwood DDX814 | Instruction Manual - Page 30
    Radio Listening Various control screens appear in the Tuner Source mode. • Set the remote controller mode switch to "AUD" mode before starting operation, see (page 91). Source Control Screen Switches to the source control screen to use various functions. 1 Display
  • Kenwood DDX814 | Instruction Manual - Page 31
    are displayed. Touch to tune in. [DISP] FM Switches the list display name to Station name or Program Service Name.*1 [CTRL] Returns to the Source Control screen. ⁄ • *1 North American sales area only. 4 Start Auto Memory Auto Memory terminates when 6 stations are stored or when all stations are
  • Kenwood DDX814 | Instruction Manual - Page 32
    Radio Listening Manual Memory Stores the current receiving station in memory. 1 Display the Source Control Screen See (page 30). 2 Select a station you wish to store in memory Radio Text (North American sales area only) You can display the radio text. (Only when receiving
  • Kenwood DDX814 | Instruction Manual - Page 33
    1 Tune in to the station to name See (page 30). 2 Start Name set Traffic Information (North American sales area only) When a traffic bulletin starts, any source is time it switches to traffic information the volume level is that from the previously adjusted and remembered
  • Kenwood DDX814 | Instruction Manual - Page 34
    Radio Listening Search by Program Type (North American sales area only) A program is tuned when you set its program type. (Only when receiving the FM broadcast) 1 Display the Source Control Screen See (page 30). 2 Enter Program Type Search mode 3 Select a Program Type 1 1
  • Kenwood DDX814 | Instruction Manual - Page 35
    is cleared automatically after approximately 5 seconds. Also, the information can be displayed automatically when it is updated. 1 2 3 1, 2 Switches to the TV screen. 3 Displays the Source Control screen. [BAND] Switches to TV1 or TV2. [4], [¢] Selects a channel. Use the [SEEK] to change the
  • Kenwood DDX814 | Instruction Manual - Page 36
    Control Screen Switches to source control screen to use various functions. 1 Display the Source Control Screen See (page 14). 2 Operation on the Source Control stations, see (page 37) or (page 37). 36 DNX9140/DDX814/DDX8034BT
  • Kenwood DDX814 | Instruction Manual - Page 37
    Screen> (page 36). 2 Select a band you wish to store in memory Manual Memory Stores the current receiving channel in memory. 1 Display the Source Control Screen See (page 36). 2 Select a station you wish to store in memory 3 Select the Auto Memory mode 3 Store in memory
  • Kenwood DDX814 | Instruction Manual - Page 38
    a name to a station. 1 Tune in to the station to name See (page 36). 2 Start Name set 3 Select a station 1 1 Memorized tune in. [ ] Switches to the TV screen. [CTRL] Returns to the Source Control screen. 3 Enter the name See (page 48) for information on
  • Kenwood DDX814 | Instruction Manual - Page 39
    /XM Control (North American sales area only) Various control screens appear in the Satellite radio source mode. (only with the optional accessory Satellite radio connected. To connect the SIRIUS tuner, a conversion cable CA-SR20V (optional accessory) is necessary and to connect the XM tuner, an XM
  • Kenwood DDX814 | Instruction Manual - Page 40
    SIRIUS/XM Control (North American sales area only) Channel Search Specifying the desired category and selecting a channel. 1 Display the Source Control Screen See (page 39). 2 Display Artist Name, to Composer Name. [ UP] Display the category list. 40 DNX9140/DDX814/DDX8034BT
  • Kenwood DDX814 | Instruction Manual - Page 41
    Direct Channel Search Tuning in by entering the desired channel number. 1 Display the Source Control Screen See (page 39). 2 Start Direct Channel Search 3 Enter the channel number 1 1 Enters the channel number. [Cancel] Cancels the direct channel search. [Clear] Clears the
  • Kenwood DDX814 | Instruction Manual - Page 42
    Radio Control (North American sales area only) Various control screens appear in the HD Radio Source mode. (only with the optional accessory HD Radio tuner connected) Source Control Screen Switches to the source control screen to use various functions. 1 Display the Source Control manually.
  • Kenwood DDX814 | Instruction Manual - Page 43
    Screen> (page 42). 2 Select a band you wish to store in memory Manual Memory Stores the current receiving station in memory. 1 Display the Source Control Screen See (page 42). 2 Select a station you wish to store in memory 3 Select the Auto Memory mode 3 Store in memory
  • Kenwood DDX814 | Instruction Manual - Page 44
    HD Radio Control (North American sales area only) Receive mode Sets the radio broadcasts receive mode. 1 Display the Source Control Screen See (page 42). 2 Display the Receive mode frequency or channel number. 4 Tune in the frequency or channel 44 DNX9140/DDX814/DDX8034BT
  • Kenwood DDX814 | Instruction Manual - Page 45
    can tag your music. When you hear a song you enjoy on your local HD Radio station, you only have to press the [ATT] button for at least 1 second. The song's information will then be saved on this unit. The saved songs will then show up in a playlist called "Purchased" in iTunes the
  • Kenwood DDX814 | Instruction Manual - Page 46
    the Source Control Screen> (page 14). 2 Operation on the Source Control Screen [3] Plays. [7] Stops playing. [8] Pauses. [4], [¢] Selects a file. ⁄ • If the Bluetooth Audio player does not support AVRCP profile, buttons are not displayed. Operate from the Audio player. 46 DNX9140/DDX814/DDX8034BT
  • Kenwood DDX814 | Instruction Manual - Page 47
    Control 1 Enter into the Voice control mode Press the TALK switch. The voice recognition icons will be attached to the buttons supporting the voice control the remote control unit is pressed. • The voice control is disabled while using your cell-phone with hands-free. • The voice control is
  • Kenwood DDX814 | Instruction Manual - Page 48
    > (page 12). 2 Display the EXT SW Control screen 1 Enters characters. [2], [3] Shifts the after you have applied the parking brake. 3 Control the external device power supply You can turn relay unit in order to use this function. Connect the external device to be controlled to that relay unit.
  • Kenwood DDX814 | Instruction Manual - Page 49
    up the phone. The system resumes playing automatically. ⁄ • To use the TEL Mute feature, you need to hook up the MUTE wire to your telephone using a commercial telephone accessory. Refer to . • Playback of the source output at the AV OUTPUT port may not be paused even a call
  • Kenwood DDX814 | Instruction Manual - Page 50
    Displayed for an NTSC system image on Video, iPod, TV or Rear View Camera. [Color] Color Control Displayed on Video, iPod, TV or Rear View Camera screen only. [Contrast] Contrast Control [Black] Black Level Adjustment [Sharpness] Sharpness control Displayed on Video, iPod, USB, TV or Rear View
  • Kenwood DDX814 | Instruction Manual - Page 51
    ⁄ • For the cell-phones which support auto-download of phonebook: If the phonebook is not downloaded automatically for some reasons, follow the procedure above to download manually. • For how to operate the cell-phone, refer to the Instruction Manual that comes with your cell-phone. • Up to
  • Kenwood DDX814 | Instruction Manual - Page 52
    Voice] (DDX814/ DDX8034BT only) Starts voice recognition. See (page 54). [BT SETUP] Displays the Bluetooth SETUP screen. of steps of the control unit is different from that of the cell-phone, the statuses displayed on the control unit may discord from those displayed
  • Kenwood DDX814 | Instruction Manual - Page 53
    that you have registered in the Phonebook. 1 Display the Hands-Free Control screen See (page 52). 2 Display the Phonebook from the cell-phone. For more details, see the instruction manual of your Bluetooth Unit and your cell-phone. • Initials including no corresponding name
  • Kenwood DDX814 | Instruction Manual - Page 54
    Outgoing Calls, Incoming Calls, or Missed Calls screen 1 Display the Hands-Free Control screen See (page 52). 2 Display the Voice Recognition or received at this unit. They are not the ones stored in the cell-phone memory. Calling by Voice Recognition (DDX814/ DDX8034BT) Calls by
  • Kenwood DDX814 | Instruction Manual - Page 55
    Services Uses tone base service using DTMF (Dual Tone Multi Frequency). 1 Display the Talking screen See (page 53). 2 Display the DTMF input screen Setting Up the Hands-Free Phone The Hands-Free system can be set as follows. 1 Display the Hands-Free Control
  • Kenwood DDX814 | Instruction Manual - Page 56
    Hands Free Unit Control [Call Beep] Sets the beep of the incoming call. ( "ON") "ON": Beep (DDX814/ DDX8034BT only) Sets whether to dial using the phone voice recognition function. ( "ON") [Echo Cancel] Sets whether to disable the units echo cancelling function. ( "ON") [Microphone Level] Adjusts
  • Kenwood DDX814 | Instruction Manual - Page 57
    Read the message for the further operation. • Repeat from 1st try if the voice is different from the 1st try. Key Word Voice Registration (DDX814/ DDX8034BT) Registers the voice to select the Phone number category by Voice Recognition. 1 Display the Hands Free Setup screen See
  • Kenwood DDX814 | Instruction Manual - Page 58
    Unit Control 5 Say the phone category to register (1st try) Say within 2 seconds after the Beep. 6 Say the phone category to register (2nd try) Say within 2 seconds after the Beep. 7 End voice registration Phone Number Preset Registers frequently used phone number to Hands Free control /DDX814/
  • Kenwood DDX814 | Instruction Manual - Page 59
    or [No] to cancel. 4 Search phone number to register with each function 5 Register phone number SMS (Short Message Service) Uses SMS function. 1 Display the Hands-Free Control screen See (page 52). 2 Display the SMS Select screen 3 Select a function [ ] Displays the SMS create
  • Kenwood DDX814 | Instruction Manual - Page 60
    Hands Free Unit Control SMS Message screen Creates a new message for the selected message. Create a message 1 Enter phone number / Select contact character Moves the cursor. [5], [∞] Scrolls up or down the character button display. [QWE]/ [ABC] Sets the key layout of the 60 DNX9140/DDX814/DDX8034BT
  • Kenwood DDX814 | Instruction Manual - Page 61
    manual, the above selection is indicated as: Touch [ ] > [ ]. 3 Select the Audio Control item Item Page [Audio Control] 61 [Equalizer] 62 [EQ] 62 [Zone Control] 63 [SRS WOW] 63 [Surround Control source may be extremely loud. [Subwoofer Level] Adjusts the subwoofer volume. [Stream
  • Kenwood DDX814 | Instruction Manual - Page 62
    iPod" is selected in , the [EQ] button is deactivated. "iPod" uses its equalizer function. 3 Select the channel to be adjusted [F] Front speaker [R] Rear speaker [C] Center speaker 4 Set the Graphic Equalizer 1 62 DNX9140/DDX814/DDX8034BT 1 Gain level can be adjusted by touching
  • Kenwood DDX814 | Instruction Manual - Page 63
    . - (page 62), (page 63), (page 64), (page 65), (page level. [FOCUS] Sets the FOCUS effect level. [SRS 3D] Sets the SRS 3D effect level. ⁄ • FOCUS: Adjusts the vertical position of the speaker and sound image
  • Kenwood DDX814 | Instruction Manual - Page 64
    ] Sets the surround position by adjusting the front and rear volume balance. [Center Width Control] Sets the vocal image position by adjusting the right and left vocal volume level. [Panorama Mode] Turns the Panorama mode On or Off. ⁄ • You cannot use the during
  • Kenwood DDX814 | Instruction Manual - Page 65
    Position You can adjust the sound effects according to your listening position. 1 Display the Position screen Touch Position]. (page 61) 2 Set the Position Control [P1] - [P3] Stores the present adjustment setup in memory, or calls it from memory. To store your adjustment in memory: Continue to
  • Kenwood DDX814 | Instruction Manual - Page 66
    the Source Select Screen [Software] 67 [System] [User Interface] 68 SRC [Touch] 69 [Clock] 69 [Security] 70 [Angle] 71 2 Display the Setup Menu Screen [EXT SW] 71 [SETUP Memory] 72 [Display] [Background] 73 [Color] 74 [Screen Adjust] 75 [Bluetooth SETUP] 75 [SIRIUS SETUP
  • Kenwood DDX814 | Instruction Manual - Page 67
    ] > [Information] > [DivX]. Software Information Checks the software version of this unit. 1 Display the Software Information screen Touch Information] > [Software]. (page 66) Displays the registration code. ⁄ • When downloading a DivX VOD file controlled by DRM, register the code appeared on the
  • Kenwood DDX814 | Instruction Manual - Page 68
    screen and audio file tags. 1 Display the User Interface screen Touch System] > [User Interface]. (page 66) 2 Display the Language Setting screen 3 Select a language [Beep] Turns the key touch tone On or Off. ( "ON") [Remote Sensor] Selects a remote control signal. ( "ON") When turned "OFF", the
  • Kenwood DDX814 | Instruction Manual - Page 69
    Setup the Clock 1 2 Follow the instruction on the screen and touch the center of navigation system or the RDS station. ( DNX9140: "Navigation", DDX814/ DDX8034BT: "OFF") "OFF"/ "RDS"*1/ "Navigation" When the synchronized mode is set, the clock cannot be adjusted manually. (*1 North American sales
  • Kenwood DDX814 | Instruction Manual - Page 70
    when the vehicle ignition is off. ( "ON") 3 Start Security Code setup ⁄ • If you have already completed the code registration, [CLR] is displayed. 4 Enter a security Code 5 Register your security code 6 Reenter the security code Reenter the same security code as that you have entered in Step 4 for
  • Kenwood DDX814 | Instruction Manual - Page 71
    Setting up power specification of the external device for which the power is controlled from this unit. 1 Display the EXT SW Setup screen Touch [ ] > [ ( mode. ( EXT SW1: Pulse, EXT SW2: Level) "Pulse": Generates a single power signal pulse. "Level": Continues output of high power signal. Sets to
  • Kenwood DDX814 | Instruction Manual - Page 72
    Setup Menu Setup Memory Audio Control, AV-IN SETUP, AV Interface, Navigation, and Audio SETUP settings can be memorized. The memorized settings can be recalled at any the current Audio Setup and AV Interface settings. [Clear] Clears the currently memorized settings. 72 DNX9140/DDX814/DDX8034BT
  • Kenwood DDX814 | Instruction Manual - Page 73
    is prohibited. Background Change Selects a image for background. 1 Select Background Change screen 2 Select a image for background 5 Select the image to load 1 1 Lists the files. [ ] When appears, the text display is scrolled by touching it. [ ROOT] Moves to the top hierarchy level. [ UP] Moves
  • Kenwood DDX814 | Instruction Manual - Page 74
    Preset button. 4 Complete the color coordination 1 Sets to the touched color. [Adjust] Sets and registers favorite color to the preset buttons ([P1] - [P3]). 74 DNX9140/DDX814/DDX8034BT
  • Kenwood DDX814 | Instruction Manual - Page 75
    setups for the menu screen. Setups for videos such as DVD can be performed on the (page 50). 3 Search for a Bluetooth unit 1 1 Displays the registered Bluetooth units. The busy service becomes active. The available service becomes inactive. [ ] When appears, the text display
  • Kenwood DDX814 | Instruction Manual - Page 76
    the searched Bluetooth unit. [Search] Searches for a Bluetooth unit. [Cancel] Cancels searching of Bluetooth unit. 5 Enter PIN code 2 Select a model name 1 1 Enters a code number using the keypad. [Enter] Confirms the entered PIN code. Enter the PIN code specified for the Bluetooth unit you are
  • Kenwood DDX814 | Instruction Manual - Page 77
    the Connect Device List screen 3 Enter PIN code 1 3 Select a registered Bluetooth unit 1 Enters a code number using the keypad. [Cancel] Cancels registration of PIN code. [Enter] Registers the entered PIN code. [Clear] Clears the code number. 4 Select the service to use [TEL (HFP)] Connects
  • Kenwood DDX814 | Instruction Manual - Page 78
    signal is entered via the AV INPUT2 port, this image is displayed. [On Screen AV-IN] Sets an on-screen display of the AV-IN playback screen. ( "Auto") "Auto": Information is displayed for 5 seconds when updated. "Manual": Information is displayed when you touch on the screen. [iPod AV Interface
  • Kenwood DDX814 | Instruction Manual - Page 79
    (page 66) 2 Set each item [On Screen Navigation] Sets an on-screen display of the navigation screen. ( "OFF") (DDX814/ DDX8034BT only) "Auto": Information is displayed for 5 seconds when updated. "OFF": Information is not displayed. [NAV Interrupt Speaker] Selects speakers used for voice guidance
  • Kenwood DDX814 | Instruction Manual - Page 80
    Bypass Control Temporarily bypassing DSP (Digital Signal Processor) System. 1 Display the Audio SETUP screen Touch [ ] > [ 66) ] > [Audio SETUP]. (page 2 Set the DSP Select [Bypass] There is no effect by DSP. [Through] There is an effect by DSP. ⁄ • When the mode is set to [Bypass Equalizer is
  • Kenwood DDX814 | Instruction Manual - Page 81
    if you have no speakers. • If you set the center speaker to "NONE" even in a short time when you are setting the Surround Control (page 64) to "Bypass+Center", the Surround Control is set to "Bypass" automatically. • If you set the center and rear speakers to "NONE" when you are setting the Surround
  • Kenwood DDX814 | Instruction Manual - Page 82
    selected, the Digital Time Alignment and Equalizer is set automatically (for timing you use together with this unit. You can choose according Dash" [Rear Speaker] Sets the location of the rear speaker. "Door", "Rear Deck" "2nd Row", "3rd Row" (Minivan, Minivan (Long)) Car Type Adjust You can manually
  • Kenwood DDX814 | Instruction Manual - Page 83
    of the vehicle interior. 2 Measure the distances from the reference point to the speakers. 3 Calculate the distance difference in accordance with the farthest speaker. Channel Level You can set the volume at each setup position. 1 Display the Car Type Setup screen Touch Audio SETUP] > [Channel
  • Kenwood DDX814 | Instruction Manual - Page 84
    Level] Displays the Parental Lock screen.*1 ( "OFF") (See
  • Kenwood DDX814 | Instruction Manual - Page 85
    66) 2 Display the Parental Level code number screen 5 Select a parental level and complete the setup 3 Enter the code number 1 Selects a parental level. ⁄ • If a disc has higher parental lock level, you need to enter the code number. • The parental lock level varies depending on a loaded disc
  • Kenwood DDX814 | Instruction Manual - Page 86
    USB Setup Performs setup when using USB. 1 Display the USB Setup screen Touch USB "Manual") "Auto": Information is displayed for 5 seconds when updated. "Manual": USB] Sets an on-screen display of the USB Playback screen. ( "Auto") "Auto": Information is displayed for 5 seconds when updated. "Manual
  • Kenwood DDX814 | Instruction Manual - Page 87
    ( "Auto") "Auto": Information is displayed for 5 seconds when updated. "Manual": Information is displayed when you touch on the screen. ⁄ • "Wide Screen" cannot be set while the iPod is connected. ⁄ • If you have already completed the code registration, [Change] is displayed. • If you want to clear
  • Kenwood DDX814 | Instruction Manual - Page 88
    to on or off, and the display returns to "SIRIUS SETUP" screen. ⁄ • If you have not registered the parental code, the code number you input in this step will be the number to register as SIRIUS Parental Code. In this case, you are requested to input the code once more. 88 DNX9140/DDX814/DDX8034BT
  • Kenwood DDX814 | Instruction Manual - Page 89
    parental lock for each channel 1 2 3 1 Channel list 2 Sets the Parental lock function on or off for each channel. You need to input the Parental code to switch the Parental lock function on or off. 3 Displays the sort sequence [Info Change] Switch the sort sequence of the channel list. ("Channel
  • Kenwood DDX814 | Instruction Manual - Page 90
    ] Sets an on-screen display of the TV screen. ( "Auto") (only when the optional accessory TV tuner connected) "Auto": Information is displayed for 5 seconds when updated. "Manual": Information is displayed when you touch on the screen. 90 DNX9140
  • Kenwood DDX814 | Instruction Manual - Page 91
    Such actions may cause the battery to leak fluid. If spilled fluid comes in contact with your eyes or on clothing, immediately rinse with water unit. TV mode Switch to this mode when controlling TV. NAVI mode Switch to this mode when controlling Navigation unit. ⁄ • The position of the remote control
  • Kenwood DDX814 | Instruction Manual - Page 92
    Remote Controller Common operations (AUD mode) Source switching Switches to the source to be played. O SRC  MENU ZOOM OUT IN O ENTER O DISP V.SEL  POSITION AUD • DVD • • Volume control T V.SEL Switches to the navigation screen. O SRC  MENU When a call comes in, it DDX814/DDX8034BT
  • Kenwood DDX814 | Instruction Manual - Page 93
    AT T Pressing this key switches the features that can be searched directly. DVD-VIDEO Title number Chapter number Play time Item number* Cancel * You may not be FM+ ANGLE O O DVD Menu Displays the DVD menu. Turns the playback control on or off while playing VCD. O ENTER O O • TV• •
  • Kenwood DDX814 | Instruction Manual - Page 94
    Remote Controller ZOOM Switches the zoom ratio each time you press this key. VIEW MAP DIR  O FM+ D O O O AM−  Y 1 1 2ABC  ANGLE ZOOM 6MNO 7PQRS CLEAR 1+ 8TUV 0 9WXYZ DIRECT # BS 2 ZONE  R.VOL  AT T • Specify the number to search in direct search. 94 DNX9140/DDX814/DDX8034BT
  • Kenwood DDX814 | Instruction Manual - Page 95
    Radio (AUD mode) Band switching Switches to bands received by the unit.  O FM+ D O O O AM−  Y 1 1 2ABC  ANGLE ZOOM 3 DEF O VOL O 2 ZONE Station selection Switches to broadcast stations received by the unit RETURN ZOOM Zooms in or out the navigation map. O SRC  MENU ZOOM OUT
  • Kenwood DDX814 | Instruction Manual - Page 96
    Remote Controller ROUTE M Displays Route Option menu. O ENTER O SUBTITLE VIEW MAP DIR ANGLE O MAP DIR Switches between the heading up navigation and north up navigation map displays. O NAVI MODE/TOP MENU FNC/MENU/PBC AUDIO channel of the station to receive. 96 DNX9140/DDX814/DDX8034BT
  • Kenwood DDX814 | Instruction Manual - Page 97
    function of the [AUD] button needs to be set to "R-CAM" beforehand. See (page 68). [Color] Sets the screen and button illumination color. (page 74) [EXT SW] Setting up power specification of the external device for which the power is controlled from this unit. (page 71) English 97
  • Kenwood DDX814 | Instruction Manual - Page 98
    the Bluetooth hands-free unit. ( unit. Orange: Error at the disc player.) "MOVIE" Identifies the video file. "MUSIC" Identifies the music file. "PICTURE" Identifies the image Seek mode is set to Manual. "PS" Indicates that received.) HD Radio "AUTO1" Indicates function is ON. XM "SEEK1" Indicates
  • Kenwood DDX814 | Instruction Manual - Page 99
    ia Interlingua sa ie Interlingue sd ik Inupiak sg id Indonesian sh Language Icelandic Italian Japanese Javanese Georgian Kazakh Romance Kirundi Romanian Russian Kinyarwanda Sanskrit Sindhi Sangho Serbo-Croatian Code Language si Singhalese sk Slovak sl Slovenian sm Samoan sn
  • Kenwood DDX814 | Instruction Manual - Page 100
    Select is Bypass. ☞ (page 80) ▲ The equalizer is set to "iPod". ☞ (page 62) ▲ The unit is set to STANDBY source. What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check
  • Kenwood DDX814 | Instruction Manual - Page 101
    . ➡ Use a USB device which this unit suppots. "Authorization Error" : Connection to the iPod has failed. ➡ Remove the iPod and then reconnect it. The unit does not support the iPod. ➡ Refer to (page 8). "Update your iPod" : The iPod's software is an
  • Kenwood DDX814 | Instruction Manual - Page 102
    unit can receive signal. "Updating Firmware" : Updating the firmware of SIRIUS tuner. ➡ Operation is invalid until the update is completed. "Updating Channels **%" : Updating . 102 DNX9140/DDX814/DDX8034BT "Off Air" : The broadcast of the selected channel has finished. "Navigation Error. Please
  • Kenwood DDX814 | Instruction Manual - Page 103
    USB interface section USB Standard : USB 2.0 High speed File System : FAT 16/ 32 Maximum Power Supply Current : 500 mA D/A Converter : 24 Bit Video Decoder : MPEG1/ MPEG2/ DivX Audio Decoder : MP3/ WMA/ AAC/ WAV Bluetooth section Technology : Bluetooth AVRCP (Audio/Video Remote Control Profile) OPP
  • Kenwood DDX814 | Instruction Manual - Page 104
    dBμ Video section Color System of External Video Input : NTSC External Video Input Level (RCA jacks) : 1 Vp-p/ 75 Ω External Audio Max Input Level (RCA jacks) : 2 V/ 25 kΩ Video Output Level (RCA jacks) : 1 Vp-p/ 75 Ω Audio Output Level (RCA jacks) : 1.2 V/ 10 kΩ Analog RGB input (DDX814/DDX8034BT
  • Kenwood DDX814 | Instruction Manual - Page 105
    Navigation section (DNX9140 only) Receiver : High-sensitivity GPS receiver Reception Frequency : 1575.42 MHz (C/A code) Acquisition Times Cold : < 38 : -20 °C - +85 °C Weight DNX9140 : 2.6 kg (5.7 lbs) DDX814/DDX8034BT : 2.55 kg (5.6 lbs) Specifications subject to change without notice. Although
  • Kenwood DDX814 | Instruction Manual - Page 106
    video the product supports, from compact portable video to high-definition video. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Kenwood iPhone" means that an electronic accessory has been designed to connect specifically to iPhone the double-D
  • Kenwood DDX814 | Instruction Manual - Page 107
    of hazardous radiation outside the unit. DNX9140/ DDX814: 2CAUTION Use of controls or adjustments or performance of radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user
  • Kenwood DDX814 | Instruction Manual - Page 108
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
GPS NAVIGATION SYSTEM
DNX9140
MONITOR WITH DVD RECEIVER
DDX814
DDX8034BT
INSTRUCTION MANUAL
©
B64-4378-10/01 (KW/RW)
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best
performance from your new GPS Navigation System/DVD Receiver.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the
warranty card, and in the space provided
below. Refer to the model and serial numbers
whenever you call upon your Kenwood dealer for information or service on the product.
Model DNX9140/DDX814/DDX8034BT
Serial number
US Residents Only
Register Online
Register your Kenwood product at
www.Kenwoodusa.com