KitchenAid KBSN702MBS Owners Manual - Page 23

Install Side Panel, Install Base Grille, Install Odor Absorber (on some models), IMPORTANT

Page 23 highlights

3. Tighten the four Torx®† 27 flat-head mounting screws to a torque of approximately 100 inch-pounds (11.3 Nm). 3. Snap the skirt onto the base grille. A. Torx® 27 flat-head mounting screws B. 1/4" hex-head mounting screws Install Side Panel If the built-in area depth is 25" (63.5 cm) or more, the side panels can be installed inside the side trim or attached to the outside of the side trim. IMPORTANT: KitchenAid is not responsible for the removal or addition of molding or decorative panels that would not allow access to the refrigerator for service. 1. For the inside side trim piece, slide the front edge of the routed side panel into the trim piece. 2. Nail the rear edge of the panel to the support board. A A. Base grille B. Skirt 4. Trim the skirt by scoring the proper "V" groove with a utility knife. Break the skirt at the score line. A. "V" groove 5. Using the 2 screws, attach the base grille assembly to the refrigerator as shown. NOTE: Drive in the right side screw first. B A. Support board (mounted to back wall) B. Cab side trim Install Base Grille There are two pieces to the base grille to allow for a custom fit: the base grille itself and the skirt. The skirt can be added to the base grille in order to extend it all the way to the floor. 1. To see whether the skirt is needed, place the base grille into position. Do not attach the base grille to the refrigerator. Measure the distance between the bottom of the base grille and the floor. The gap must be a minimum of 1/2" (1.27 cm) in order to add the skirt. NOTE: If the gap measures less than1/2" (1.27 cm), skip steps 3 and 4 of the instructions, and install the base grille only. 2. Remove the film from the base grille. A. Screws (2) Install Odor Absorber (on some models) On some models, your refrigerator's accessory packet includes an odor absorber, which must be installed prior to use. On some models, the odor absorber is already installed at the factory. The odor absorber reduces the buildup of odors. This helps to maintain a cleaner environment inside the refrigerator. 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72

23
3.
Tighten the four Torx®† 27 flat-head mounting screws to a
torque of approximately 100 inch-pounds (11.3 Nm).
A.
Torx® 27 flat-head mounting screws
B.
1/4" hex-head mounting screws
Install Side Panel
If the built-in area depth is 25" (63.5 cm) or more, the side panels
can be installed inside the side trim or attached to the outside of
the side trim.
IMPORTANT:
KitchenAid is not responsible for the removal or
addition of molding or decorative panels that would not allow
access to the refrigerator for service.
1.
For the inside side trim piece, slide the front edge of the routed
side panel into the trim piece.
2.
Nail the rear edge of the panel to the support board.
A.
Support board (mounted to back wall)
B.
Cab side trim
Install Base Grille
There are two pieces to the base grille to allow for a custom fit: the
base grille itself and the skirt. The skirt can be added to the base
grille in order to extend it all the way to the floor.
1.
To see whether the skirt is needed, place the base grille into
position. Do not attach the base grille to the refrigerator.
Measure the distance between the bottom of the base grille
and the floor. The gap must be a minimum of 1/2" (1.27 cm) in
order to add the skirt.
NOTE:
If the gap measures less than1/2" (1.27 cm), skip
steps 3 and 4 of the instructions, and install the base grille
only.
2.
Remove the film from the base grille.
3.
Snap the skirt onto the base grille.
A.
Base grille
B.
Skirt
4.
Trim
the
skirt
by
scoring
the
proper
V
groove
with
a
utility
knife. Break the skirt at the score line.
A.
“V” groove
5.
Using the 2 screws, attach the base grille assembly to the
refrigerator as shown.
NOTE:
Drive in the right side screw first.
A.
Screws (2)
Install
Odor
Absorber
(on
some
models)
On
some
models,
your
refrigerator
s
accessory
packet
includes
an
odor
absorber,
which
must
be
installed
prior
to
use.
On
some
models,
the
odor
absorber
is
already
installed
at
the
factory.
The odor absorber reduces the buildup of odors. This helps to
maintain a cleaner environment inside the refrigerator.
A
B