KitchenAid KBSN702MBS Owners Manual - Page 25

REFRIGERATOR FEATURES, Water and Ice Dispensers

Get KitchenAid KBSN702MBS PDF manuals and user guides View all KitchenAid KBSN702MBS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

1. Turn on the ice maker. Lower the wire shutoff arm as shown. Please refer to "Ice Maker and Storage Bin" for further instructions on the operation of your ice maker. NOTE: � Allow 24 hours to produce the first batch of ice. � Allow 3 days to completely fill ice container. � Depending on your model, you may want to select the maximum ice feature to increase the production of ice. REFRIGERATOR FEATURES Water and Ice Dispensers Please read before using the water system. Follow the directions specific to your model. Style 1 (Dispenser Models) IMPORTANT: � After connecting the refrigerator to a water source or replacing the water filter, follow the steps below to make sure that the water system is properly cleaned. This will flush air from the filter and water dispensing system, and prepare the water filter for use. � Connect to potable water supply only. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts. NOTE: If your model has a base grille filter system, make sure the base grille filter is properly installed and the cap is in the horizontal position. 1. Open the freezer door and turn off the ice maker. The ON/OFF switch is located on the top right side of the freezer compartment. Move the switch to the OFF (right) setting as shown. 2. Use a sturdy container to depress and hold the water dispenser lever for 5 seconds, then release it for 5 seconds. Repeat until water begins to flow. Once water begins to flow, continue depressing and releasing the dispenser lever (5 seconds on, 5 seconds off) until a total of 3 gallons (12 L) has been dispensed. This will flush air from the filter and water dispensing system and prepare the water filter for use. Additional flushing may be required in some households. NOTE: As air is cleared from the system, water may spurt out of the dispenser. 3. Open the freezer door and turn on the ice maker. Move the switch to the ON (left) position. Notes: � Allow 24 hours to produce the first batch of ice. � Discard the first three batches of ice produced. � Allow 3 days to completely fill ice container. Style 2 (Non-Dispenser Models) IMPORTANT: After connecting the refrigerator to a water source or replacing the water filter, fill and discard two full containers of ice to prepare the water filter for use, before using the ice. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts. NOTE: If your model has a base grille filter system, make sure the base grille filter is properly installed and the cap is in the horizontal position. 1. For icemakers with a switch, use the switch to turn ON or Off the icemaker. Without switch With switch Notes: � Allow 24 hours to produce the first batch of ice. � Allow 3 days to completely fill ice container. � Depending on your model, you may want to select the maximum ice feature to increase the production of ice. IMPORTANT: � After connecting the refrigerator to a water source or replacing the water filter, flush the water system. Use a sturdy container to depress and hold the water dispenser lever for 5 seconds, then release it for 5 seconds. Repeat until water begins to flow. Once water begins to flow, continue depressing and releasing the dispenser lever (5 seconds on, 5 seconds off) until a total of 3 gallons (12 L) has been dispensed. This will flush air from the filter and water dispensing system, and prepare the water filter for use. Additional flushing may be required in some households. NOTE: As air is cleared from the system, water may spurt out of the dispenser. � Allow 24 hours for the refrigerator to cool down and chill water. � Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. � The dispensing system will not operate when the freezer door is open. � Depending on your model, your water and ice dispensers may have one or more of the following features: A dispenser tray, a special light that turns on when you use the dispenser, or a lock option to avoid unintentional dispensing. 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
25
1.
Turn on the ice maker. Lower the wire shutoff arm as shown.
Please refer to “Ice Maker and Storage Bin” for further
instructions on the operation of your ice maker.
NOTE:
�
Allow 24 hours to produce the first batch of ice.
�
Allow 3 days to completely fill ice container.
�
Depending on your model, you may want to select the
maximum ice feature to increase the production of ice.
REFRIGERATOR FEATURES
Water and Ice Dispensers
Please read before using the water system. Follow the directions
specific to your model.
Style 1 (Dispenser Models)
IMPORTANT:
�
After connecting the refrigerator to a water source or replacing
the water filter, follow the steps below to make sure that the
water system is properly cleaned. This will flush air from the
filter and water dispensing system, and prepare the water filter
for use.
�
Connect to potable water supply only.
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the
system. Systems certified for cyst reduction may be used on
disinfected waters that may contain filterable cysts.
NOTE:
If your model has a base grille filter system, make sure the
base grille filter is properly installed and the cap is in the horizontal
position.
1.
Open the freezer door and turn off the ice maker. The ON/OFF
switch is located on the top right side of the freezer
compartment. Move the switch to the OFF (right) setting as
shown.
2.
Use a sturdy container to depress and hold the water
dispenser
lever
for
5
seconds,
then
release
it
for
5
seconds.
Repeat
until
water
begins
to
flow.
Once
water
begins
to
flow,
continue
depressing
and
releasing
the
dispenser
lever
(5
seconds
on,
5
seconds
off)
until
a
total
of
3
gal
lons
(12
L)
has
been
dispensed.
This
will
flush
air
from
the
filter
and
water
dispensing
system
and
prepare
the
water
filter
for
use.
Additional
flushing
may
be
required
in
some
households.
NOTE:
As
air
is
cleared
from
the
system,
water
may
spurt
out
of
the
dispenser.
3.
Open the freezer door and turn on the ice maker. Move the
switch to the ON (left) position.
Notes:
�
Allow 24 hours to produce the first batch of ice.
�
Discard the first three batches of ice produced.
�
Allow 3 days to completely fill ice container.
Style 2 (Non-Dispenser Models)
IMPORTANT:
After connecting the refrigerator to a water source
or replacing the water filter, fill and discard two full containers of
ice to prepare the water filter for use, before using the ice.
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the
system. Systems certified for cyst reduction may be used on
disinfected waters that may contain filterable cysts.
NOTE:
If your model has a base grille filter system, make sure the
base grille filter is properly installed and the cap is in the horizontal
position.
1.
For icemakers with a switch, use the switch to turn ON or Off
the icemaker.
Without switch
With switch
Notes:
�
Allow 24 hours to produce the first batch of ice.
�
Allow 3 days to completely fill ice container.
�
Depending on your model, you may want to select the
maximum ice feature to increase the production of ice.
IMPORTANT:
�
After
connecting
the
refrigerator
to
a
water
source
or
replacing
the
water
filter,
flush
the
water
system.
Use
a
sturdy
container
to
depress
and
hold
the
water
dispenser
lever
for
5
seconds,
then
release
it
for
5
seconds.
Repeat
until
water
begins
to
flow.
Once
water
begins
to
flow,
continue
depressing
and
releasing
the
dispenser
lever
(5
seconds
on,
5
seconds
off)
until
a
total
of
3
gal
lons
(12
L)
has
been
dispensed.
This
will
flush
air
from
the
filter
and
water
dispensing
system,
and
prepare
the
water
filter
for
use.
Additional
flushing
may
be
required
in
some
households.
NOTE:
As
air
is
cleared
from
the
system,
water
may
spurt
out
of
the
dispenser.
�
Allow
24
hours
for
the
refrigerator
to
cool
down
and
chill
water.
�
Allow
24
hours
to
produce
the
first
batch
of
ice.
Discard
the
first
three
batches
of
ice
produced.
�
The
dispensing
system
will
not
operate
when
the
freezer
door
is
open.
�
Depending
on
your
model,
your
water
and
ice
dispensers
may
have
one
or
more
of
the
following
features:
A
dispenser
tray,
a
special
light
that
turns
on
when
you
use
the
dispenser,
or
a
lock
option
to
avoid
unintentional
dispensing.