KitchenAid KSSC42QTS Installation Guide - Page 16

Panels, Routing, Requirements, Standard, Handle - Top View, Door Panel - Side View, Extended, Handle - trim kit

Get KitchenAid KSSC42QTS - 42inch Refrigerator PDF manuals and user guides
UPC - 883049038155
View all KitchenAid KSSC42QTS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

½" (1.3._m) _ 1/4" (6.35 mm) max. { Top ] Door Panel - Side View j- C 13_ rnln. _- / Center face detail between _--._._._._ offsets ! [._- %,, __ / 7,1 (17.8 cm) 1/2" __ _cm) Bottom (6.35 mm) max. Door Panels - Routing Requirements If the custom panels are thicker than 1/4"(6.35 mm), then all edges of the panels must be routed• If the standard handle is used, route the entire handle side of both panels 31/4'' (8.25 cm) to allow for finger clearance. Then route the other sides 1" (2.54 cm). Standard Handle - Top View Extended Handle - Top View _ (6.35 mm) j 1/4, ' :% 1" (2.54 cm) max _/ Hinge Side 1" (2.54 cm) 31/4" (8.26 cm) rnln. Q Door 1/4"(6.36 ram) max. I Panel I [ I Hinge Side __] Panel Door !_,. 2" (5 cm) min. 1u (2.54 cm) If an extended handle kit is used, route the handle side 1/4" (6.35 mm). All other routing dimensions would remain the same as the standard handle. Make sure your product location will allow doors with extended handles to be opened to 90 degrees. See "Door Swing Dimensions." For more information on ordering extended handles, see "Classic Series Factory Panels and Kits." NOTE: For both types of handles, route the top and bottom edges 1/2"(1.3 cm). .......... ......... ............ d ..... Custom side panels may be needed when not enough space is available to have cabinets on both sides of the refrigerator or when the refrigerator is placed at the end of a cabinet run. You may choose an Inset, Flush, or Recessed Inset panel installation. Refrigerator and Side Trim Dimensions The width and height of a side panel are determined by the type of installation you are planning• NOTES: • The dimensions shown are actual product dimensions and may not reflect the needed panel installation dimensions. • The side panel should be a minimum of 1/_,,(1.27 cm) thick to avoid warping. • If the opening depth is 25" (63.5 cm) or more, you may want to install a support board on rear wall. Refrigerator 't241/s. (61,3 cm) (60,3 cm) 231/2 '' (59,7 crn) 2311/1e" 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
½"
{
(1.3._m)
]
rnln.
_-
/
Center face
detail between _--._._._._
offsets
!
[._-
%,,
__
1/2"
__
_cm)
/
_
1/4"
(6.35 mm)
max.
Top
7,1
(17.8 cm)
Bottom
(6.35 mm)
max.
Door
Panels
- Routing
Requirements
If the custom
panels are thicker than 1/4"(6.35 mm), then all edges
of the panels must be routed•
If the standard
handle
is used,
route the entire handle side of both panels 31/4
'' (8.25 cm) to allow
for finger clearance.
Then route the other sides 1" (2.54 cm).
Standard
Handle - Top View
Door Panel - Side View
j-
C
13_
Extended
Handle
-
Top View
j
1/4,
'
_
(6.35
mm)
:%
1"
(2.54 cm)
max
_/
Hinge Side
1"
(2.54
cm)
I
31/4"
(8.26 cm)
rnln.
Q
1/4"
(6.36
ram)
max.
I
[
I
2"
(5 cm)
min.
Door
Panel
Hinge Side
__]
Door
!_,.
Panel
1u
(2.54 cm)
If an extended
handle kit is used, route the handle
side 1/4"
(6.35 mm). All other routing
dimensions
would
remain the same
as the standard
handle. Make sure your product
location
will
allow doors
with extended
handles
to be opened
to 90 degrees.
See "Door
Swing Dimensions."
For more information
on ordering extended
handles, see "Classic
Series Factory Panels and Kits."
NOTE: For both types
of handles,
route the top and bottom
edges 1/2"(1.3 cm).
..........
.........
............
d
.....
Custom
side panels may be needed
when not enough
space is
available to have cabinets
on both sides of the refrigerator
or
when the refrigerator
is placed at the end of a cabinet
run. You
may choose
an Inset, Flush, or Recessed
Inset panel installation.
Refrigerator
and Side Trim Dimensions
The width
and height
of a side panel are determined
by the type
of installation
you are planning•
NOTES:
•
The dimensions
shown
are actual product
dimensions
and may not reflect the needed
panel installation
dimensions.
•
The side panel should be a minimum
of 1/_,,(1.27 cm) thick
to avoid
warping.
•
If the opening
depth
is 25" (63.5 cm) or more, you may
want to install a support
board on rear wall.
Refrigerator
't
241/s.
(61,3
cm)
2311/1e"
(60,3
cm)
231/2 ''
(59,7
crn)
16