Konica Minolta C83hc High Chroma EF-103 AccurioPress C3080/C3080P/C3070/Print - Page 18

Installing Parts in the Tray (when Large Capacity Unit LU-202m/LU- 202XL/LU-202XLm is installed)

Get Konica Minolta C83hc High Chroma PDF manuals and user guides View all Konica Minolta C83hc High Chroma manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

2.2 Installation Procedures 2 2.2.3 Installing Parts in the Tray (when Large Capacity Unit LU-202m/LU202XL/LU-202XLm is installed) The auxiliary parts that need to be installed to the Large Capacity Unit LU-202m/LU-202XL/LU-202XLm vary depending on the size of the envelope to be used. For details on the envelope size, refer to page 5-2. Using C5, C6/C5, or 6x9 1/2 Envelopes The following parts need to be installed when C5, C6/C5, or 6x9 1/2 envelopes are used. - Bottom auxiliary guide assy [A] (1 piece) - Adjusting block assy (2 pieces) - Tip auxiliary guide/rear assy [C] (1 piece) - Tip auxiliary guide/front assy [C] (1 piece) - Bottom auxiliary plate assy [D] (1 piece) - Guide shaft (1 piece) Follow the procedure below to use envelopes of the above size. Auxiliary guides (2 pieces) are not needed. 1 Open the upper door. 2 Remove the holding paper. % Hold the projection with your fingers and slide the holding paper in the arrowed direction, and remove it. 3 Install the bottom auxiliary guide assy [A] in the Large Ca- pacity Unit LU-202m/LU-202XL/LU-202XLm tray. % Align the positioning pin of the bottom auxiliary guide assy [A] with the installation hole of the tray. % Align the detent of the bottom auxiliary guide assy [A] with the groove on the back end guide. AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 2-10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L
2-10
2.2
Installation Procedures
2
2.2.3
Installing Parts in the Tray (when Large Capacity Unit LU-202m/LU-
202XL/LU-202XLm is installed)
The auxiliary parts that need to be installed to the Large Capacity Unit LU-202m/LU-202XL/LU-202XLm vary
depending on the size of the envelope to be used.
For details on the envelope size, refer to
page 5-2
.
Using C5, C6/C5, or 6x9 1/2 Envelopes
The following parts need to be installed when C5, C6/C5, or 6x9 1/2 envelopes are used.
-
Bottom auxiliary guide assy [A] (1 piece)
-
Adjusting block assy (2 pieces)
-
Tip auxiliary guide/rear assy [C] (1 piece)
-
Tip auxiliary guide/front assy [C] (1 piece)
-
Bottom auxiliary plate assy [D] (1 piece)
-
Guide shaft (1 piece)
Follow the procedure below to use envelopes of the above size. Auxiliary guides (2 pieces) are not needed.
1
Open the upper door.
2
Remove the holding paper.
%
Hold the projection with your fingers and slide the hold-
ing paper in the arrowed direction, and remove it.
3
Install the bottom auxiliary guide assy [A] in the Large Ca-
pacity Unit LU-202m/LU-202XL/LU-202XLm tray.
%
Align the positioning pin of the bottom auxiliary guide
assy [A] with the installation hole of the tray.
%
Align the detent of the bottom auxiliary guide assy [A]
with the groove on the back end guide.