Konica Minolta C83hc High Chroma EF-103 AccurioPress C3080/C3080P/C3070/Print - Page 23

Using K1 270 x 382 mm or K0 287 x 382 mm Envelopes

Get Konica Minolta C83hc High Chroma PDF manuals and user guides View all Konica Minolta C83hc High Chroma manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

2.2 Installation Procedures 2 5 Install the side auxiliary guide assy [B] to the paper guide side plate. (2 places) % Be sure to align the installation holes in the side auxiliary guide assy with the positioning screws. NOTICE Turn the machine power on, and lower the tray bottom plate to the lowest place by pressing the tray bottom plate lowering button of the Large Capacity Unit LU-202m/LU202XL/LU-202XLm, and then install the side auxiliary guide assy [B]. An incorrect setting may result in damage to the machine. Bottom plate lowering button 6 Install the guide shaft to the back edge guide base of the bottom auxiliary guide assy [A]. 7 Close the upper door. Using K1 (270 x 382 mm) or K0 (287 x 382 mm) Envelopes The following parts need to be installed when K1 or K0 envelopes are used. - Bottom auxiliary guide assy [A] (1 piece) - Adjusting block assy (2 pieces) - Bottom auxiliary plate assy [D] (1 piece) NOTICE In the case of K1 or K0 envelopes, depending on the curl direction, the paper can also be fed without the use of auxiliary parts. For details, refer to page 2-16. 1 Open the upper door. 2 Remove the holding paper. % Hold the projection with your fingers and slide the holding paper in the arrowed direction, and remove it. % Check the curl direction at the leading edge of the envelope, and remove the holding paper, if necessary. AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 2-15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L
2-15
2.2
Installation Procedures
2
5
Install the side auxiliary guide assy [B] to the paper guide
side plate. (2 places)
%
Be sure to align the installation holes in the side auxil-
iary guide assy with the positioning screws.
NOTICE
Turn the machine power on, and lower the tray bottom
plate to the lowest place by pressing the tray bottom plate
lowering button of the Large Capacity Unit LU-202m/LU-
202XL/LU-202XLm, and then install the side auxiliary
guide assy [B]. An incorrect setting may result in damage
to the machine.
6
Install the guide shaft to the back edge guide base of the
bottom auxiliary guide assy [A].
7
Close the upper door.
Using K1 (270 x 382 mm) or K0 (287 x 382 mm) Envelopes
The following parts need to be installed when K1 or K0 envelopes are used.
-
Bottom auxiliary guide assy [A] (1 piece)
-
Adjusting block assy (2 pieces)
-
Bottom auxiliary plate assy [D] (1 piece)
NOTICE
In the case of K1 or K0 envelopes, depending on the curl direction, the paper can also be fed without the use
of auxiliary parts. For details, refer to
page 2-16
.
1
Open the upper door.
2
Remove the holding paper.
%
Hold the projection with your fingers and slide the hold-
ing paper in the arrowed direction, and remove it.
%
Check the curl direction at the leading edge of the en-
velope, and remove the holding paper, if necessary.
Bottom plate lowering button