Konica Minolta C83hc High Chroma EF-103 AccurioPress C3080/C3080P/C3070/Print - Page 22

Using N4 90 x 205 mm or N3 120 x 235 mm Envelopes

Get Konica Minolta C83hc High Chroma PDF manuals and user guides View all Konica Minolta C83hc High Chroma manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

2.2 Installation Procedures 2 Using N4 (90 x 205 mm) or N3 (120 x 235 mm) Envelopes The following parts need to be installed when N4 or N3 envelopes are used. - Bottom auxiliary guide assy [A] (1 piece) - Adjusting block assy (2 pieces) - Side auxiliary guide assy [B] (2 pieces) - Guide shaft (1 piece) 1 Open the upper door. 2 Remove the holding paper. % Hold the projection with your fingers and slide the holding paper in the arrowed direction, and remove it. 3 Install the bottom auxiliary guide assy [A] in the Large Ca- pacity Unit LU-202m/LU-202XL/LU-202XLm tray. % Align the positioning pin of the bottom auxiliary guide assy [A] with the installation hole of the tray. % Align the detent of the bottom auxiliary guide assy [A] with the groove on the back end guide. 4 Align the adjusting block assies (2 pieces) to N4 and N3 on the indicating label, and install them. % Align the mark on the adjusting block assy with the mark on the indicating label. N4 (90 x 205 mm),  N3 (120 x 235mm) AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 2-14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L
2-14
2.2
Installation Procedures
2
Using N4 (90 x 205 mm) or N3 (120 x 235 mm) Envelopes
The following parts need to be installed when N4 or N3 envelopes are used.
-
Bottom auxiliary guide assy [A] (1 piece)
-
Adjusting block assy (2 pieces)
-
Side auxiliary guide assy [B] (2 pieces)
-
Guide shaft (1 piece)
1
Open the upper door.
2
Remove the holding paper.
%
Hold the projection with your fingers and slide the hold-
ing paper in the arrowed direction, and remove it.
3
Install the bottom auxiliary guide assy [A] in the Large Ca-
pacity Unit LU-202m/LU-202XL/LU-202XLm tray.
%
Align the positioning pin of the bottom auxiliary guide
assy [A] with the installation hole of the tray.
%
Align the detent of the bottom auxiliary guide assy [A]
with the groove on the back end guide.
4
Align the adjusting block assies (2 pieces) to N4 and N3 on
the indicating label, and install them.
%
Align the mark on the adjusting block assy with the
mark on the indicating label.
N4 (90 x 205 mm),
N3 (120 x 235mm)