LG LSS-3200A Owners Manual - Page 72

Step 3. Signal Strength, To see the signal strength

Get LG LSS-3200A PDF manuals and user guides View all LG LSS-3200A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

8. CUSTOMIZATION 8-7. Initializing the System Step 3. Signal Strength Depending on the Dish Type you have selected, the Signal Strength menu shows you up to three signal strength bars for Satellite Networks A, B, and C, in order to help you adjust the dish to the correct position with the elevation, azimuth, and tilt values obtained from the Your Location menu. While the maximum signal strength is 100, there will be no apparent difference in picture quality between signal strengths of 60 to 85. The higher the signal, the less likely you are to experience picture quality degradation during adverse weather conditions such as heavy rain or snow. A transponder is a receiver/transmitter on the satellite. It receives signals from DIRECTV and retransmits them to your dish. The DIRECTV® HD Receiver is capable of displaying the signal strength of most transponders by using the following method. To see the signal strength: 1. Move the highlight to select the desired satellite using "FG". 2. Set an each transponder using "DE" 3. Press " " to move to the next step of the initial setup. NOTE NOTE Depending on your location in the If you have selected an Oval Dish and United States, certain transponders SAT B and/or SAT C do not display a may not be available. It is normal for signal strength on any transponder, re- the signal strength level of a few check your dish installation or perform 71 transponders to be at zero. Step 1: Dish Setup again.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
71
8-7. Initializing the System
Step 3. Signal Strength
Depending on the Dish Type you have selected, the Signal Strength menu shows you up to three sig-
nal strength bars for Satellite Networks A, B, and C, in order to help you adjust the dish to the cor-
rect position with the elevation, azimuth, and tilt values obtained from the Your Location menu.
While the maximum signal strength is 100, there will be no apparent difference in picture quality
between signal strengths of 60 to 85. The higher the signal, the less likely you are to experience pic-
ture quality degradation during adverse weather conditions such as heavy rain or snow.
A transponder is a receiver/transmitter on the satellite. It receives signals from DIRECTV and retrans-
mits them to your dish. The DIRECTV
®
HD Receiver is capable of displaying the signal strength of
most transponders by using the following method.
To see the signal strength:
1.
Move the highlight to select the desired
satellite
using “
FG
”.
2.
Set an each
transponder
using “
DE
”
3.
Press “
” to move to the next step of the initial setup.
8. CUSTOMIZATION
NOTE
Depending on your location in the
United States, certain transponders
may not be available. It is normal for
the signal strength level of a few
transponders to be at zero.
NOTE
If you have selected an Oval Dish and
SAT B and/or SAT C do not display a
signal strength on any transponder, re-
check your dish installation or perform
Step 1: Dish Setup again.