Lenovo 6234A1U User Manual - Page 24

Installing or replacing a memory module, Notes

Get Lenovo 6234A1U PDF manuals and user guides View all Lenovo 6234A1U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

2. On some models, you might need to pivot the drive bay assembly upward and remove the hard disk drive to access the internal components. See "Replacing the hard disk drive" on page 23. Notes: a. Make sure you note the locations of any cables that you disconnect from the drives or the system board. b. Make sure the hard disk drive assembly is in the latched down position before closing the computer cover to prevent damage to the hard disk drive assembly. Figure 6. Pivoting the drive bay assembly Installing or replacing a memory module Attention Do not open your computer or attempt any repair before reading and understanding the "Important safety information" in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to install or replace a memory module. Your computer has two slots for installing or replacing DDR2 DIMMs. When installing or replacing a memory module, use 1 GB or 2 GB DDR2 DIMMs in any combination up to a maximum of 4 GB system memory. 16 User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
2.
On some models, you might need to pivot the drive bay assembly upward and
remove the hard disk drive to access the internal components. See “Replacing
the hard disk drive” on page 23.
Notes:
a.
Make sure you note the locations of any cables that you disconnect from the
drives or the system board.
b.
Make sure the hard disk drive assembly is in the latched down position
before closing the computer cover to prevent damage to the hard disk drive
assembly.
Installing or replacing a memory module
Attention
Do not open your computer or attempt any repair before reading and understanding the
“Important safety information” in the
ThinkCentre Safety and Warranty Guide
that came with
your computer. To obtain a copy of the
ThinkCentre Safety and Warranty Guide
, go to:
This section provides instructions on how to install or replace a memory module.
Your computer has two slots for installing or replacing DDR2 DIMMs. When
installing or replacing a memory module, use 1 GB or 2 GB DDR2 DIMMs in any
combination up to a maximum of 4 GB system memory.
Figure 6. Pivoting the drive bay assembly
16
User Guide