Lenovo NetVista Hardware Maintenance Manual (HMM) for Aptiva, IBM PC300, and N - Page 58

Table 2-1 BIOS Error Codes, Messages, and Beeps List

Get Lenovo NetVista PDF manuals and user guides View all Lenovo NetVista manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Table 2-1 BIOS Error Codes, Messages, and Beeps List BIOS Error Codes, Messages, beeps Action/FRU NOTE: To diagnose a problem, first find the BIOS error messages, codes, or beeps in left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause. 201 Memory test failure. 301 Keyboard error or no keyboard present. Insert the memory modules in the DIMM sockets properly, and then reboot the system. Memory module. See the "Step 005" of "Memory" on page 74 to replace memory module. System board. Make sure the keyboard is connected properly and are set correctly in BIOS Setup. System board. 662 Unable to reset floppy subsystem. FLOPPY DISK(S) failure (80) 662 Floppy Type mismatch. FLOPPY DISK(S) failure (40) 1701 Make sure the hard disks are set correctly in BIOS Hard disk(s) Diagnosis setup. failure Hard disk drive cable/connection. Hard disk drive. System board. 1762 Make sure that the System Boot Drive parameter in the Primary master IDE has changed Startup Options of BIOS Setup is not set to [Drive A only]. Primary slave IDE has Load default settings in Setup. changed Insert a system diskette into diskette drive and reboot Secondary master IDE system. has changed Make sure the diskette drive configuration setting in Secondary slave IDE BIOS Setup is correct. has changed Hard disk drive power. 1780 Primary master hard disk failure Diskette drive. System board. A warning message to indicate there has been a change of IDE Primary (Secondary) Channel Master (Slave) device. Load default settings in Setup. 1781 Check IDE drive jumper. See "3.5-In. Hard Disk Drive Jumper Locations" on page 131. Primary slave hard disk failure IDE drive power. IDE drive cable/connection. IDE drive. 58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
58
Table 2-1 BIOS Error Codes, Messages, and Beeps List
BIOS Error Codes,
Messages, beeps
Action/FRU
NOTE: To diagnose a problem, first find the BIOS error messages, codes, or
beeps in left column. If directed to a check procedure, replace the FRU indicated
in the check procedure. If no check procedure is indicated, the first Action/FRU
listed in right column is the most likely cause.
201
Memory test failure.
Insert the memory modules in the DIMM sockets
properly, and then reboot the system.
Memory module. See the “Step 005” of ”Memory” on
page 74 to replace memory module.
System board.
301
Keyboard error or no
keyboard present.
Make sure the keyboard is connected properly and are
set correctly in BIOS Setup.
System board.
662
FLOPPY DISK(S)
failure (80)
Unable to reset floppy subsystem.
662
FLOPPY DISK(S)
failure (40)
Floppy Type mismatch.
1701
Hard disk(s) Diagnosis
failure
Make sure the hard disks are set correctly in BIOS
setup.
Hard disk drive cable/connection.
Hard disk drive.
System board.
1762
Primary master IDE has
changed
Primary slave IDE has
changed
Secondary master IDE
has changed
Secondary slave IDE
has changed
Make sure that the System Boot Drive parameter in the
Startup Options of BIOS Setup is not set to [Drive A
only].
Load default settings in Setup.
Insert a system diskette into diskette drive and reboot
system.
Make sure the diskette drive configuration setting in
BIOS Setup is correct.
Hard disk drive power.
Diskette drive.
System board.
1780
Primary master hard
disk failure
1781
Primary slave hard disk
failure
A warning message to indicate there has been a
change of IDE Primary (Secondary) Channel Master
(Slave) device.
Load default settings in Setup.
Check IDE drive jumper. See “3.5-In. Hard Disk Drive
Jumper Locations” on page 131.
IDE drive power.
IDE drive cable/connection.
IDE drive.