Lenovo ThinkCentre M91p Hardware Maintenance Manual - Page 59

USB port Device Controller failure, USB port Interface Test Passed

Get Lenovo ThinkCentre M91p PDF manuals and user guides View all Lenovo ThinkCentre M91p manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Diagnostic Error Code 006-196-XXX Diskette interface test halt, error threshold exceeded 006-197-XXX Diskette interface test warning 006-198-XXX Diskette interface test aborted 006-199-XXX Diskette interface test failed, cause unknown 006-25X-XXX Diskette interface Error 015-000-XXX USB port Interface Test Passed 015-001-XXX USB port Presence 015-002-XXX USB port Timeout 015-015-XXX USB port External Loopback failure 015-027-XXX USB port Configuration/Setup error 015-032-XXX USB port Device Controller failure 015-034-XXX USB port buffer allocation failure 015-035-XXX USB port Reset condition detected 015-036-XXX USB port Register error 015-040-XXX USB port IRQ failure 015-195-XXX USB port Test aborted by user FRU/Action 1. Press F3 to review the log file. 2. Restart the test to reset the log file. 1. If a component is called out, make sure it is connected and/or enabled . 2. Re-run the test. 3. Replace the component that is called out in warning statement. 4. Replace the component under test. 1. If a component is called out, make sure it is connected and/or enabled. 2. Flash the system and re-test. See "Updating (flashing) the BIOS from a disc" on page 186. 3. Go to "Undetermined problems" on page 66. 1. Go to "Undetermined problems" on page 66. 2. Flash the system and re-test. 3. Replace component under function test. 1. Diskette drive cable 2. Diskette drive 3. System board No action 1. Remove USB device(s) and re-test 2. System board 1. Remove USB device(s) and re-test 2. System board 1. Remove USB device(s) and re-test 2. System board 1. Flash the system. See "Updating (flashing) the BIOS from a disc" on page 186. 2. System board System board 1. Reboot the system 2. Flash the system and re-test. See "Updating (flashing) the BIOS from a disc" on page 186. 3. Run memory test 4. System board 1. Remove USB device(s) and re-test. 2. System board System board 1. Run the Setup Utility program and check for conflicts. 2. Flash the system. See "Updating (flashing) the BIOS from a disc" on page 186. 3. System board Information only Restart the test, if necessary. Chapter 7. Symptom-to-FRU index 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
Diagnostic Error Code
FRU/Action
006-196-XXX
Diskette interface test halt, error threshold
exceeded
1. Press F3 to review the log file.
2. Restart the test to reset the log file.
006-197-XXX
Diskette interface test warning
1. If a component is called out, make sure it is
connected and/or enabled .
2. Re-run the test.
3. Replace the component that is called out in warning
statement.
4. Replace the component under test.
006-198-XXX
Diskette interface test aborted
1. If a component is called out, make sure it is
connected and/or enabled.
2. Flash the system and re-test. See “Updating
(flashing) the BIOS from a disc” on page 186.
3. Go to “Undetermined problems” on page 66.
006-199-XXX
Diskette interface test failed, cause
unknown
1. Go to “Undetermined problems” on page 66.
2. Flash the system and re-test.
3. Replace component under function test.
006-25X-XXX
Diskette interface Error
1. Diskette drive cable
2. Diskette drive
3. System board
015-000-XXX
USB port Interface Test Passed
No action
015-001-XXX
USB port Presence
1. Remove USB device(s) and re-test
2. System board
015-002-XXX
USB port Timeout
1. Remove USB device(s) and re-test
2. System board
015-015-XXX
USB port External Loopback failure
1. Remove USB device(s) and re-test
2. System board
015-027-XXX
USB port Configuration/Setup error
1. Flash the system. See “Updating (flashing) the BIOS
from a disc” on page 186.
2. System board
015-032-XXX
USB port Device Controller failure
System board
015-034-XXX
USB port buffer allocation failure
1. Reboot the system
2. Flash the system and re-test. See “Updating
(flashing) the BIOS from a disc” on page 186.
3. Run memory test
4. System board
015-035-XXX
USB port Reset condition detected
1. Remove USB device(s) and re-test.
2. System board
015-036-XXX
USB port Register error
System board
015-040-XXX
USB port IRQ failure
1. Run the Setup Utility program and check for conflicts.
2. Flash the system. See “Updating (flashing) the BIOS
from a disc” on page 186.
3. System board
015-195-XXX
USB port Test aborted by user
Information only Restart the test, if necessary.
Chapter 7
.
Symptom-to-FRU index
53