Lenovo ThinkPad Edge E125 Hardware Maintenance Manual - Page 54

Retaining serial numbers, Restoring the serial number of the system unit, Notes, Torque

Get Lenovo ThinkPad Edge E125 PDF manuals and user guides View all Lenovo ThinkPad Edge E125 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Notes: • If you have a torque driver, refer to the Torque column in the screw information table for each step. • Make sure that you use the correct screw. It is recommended to use new screws for replacements. If you have a torque screwdriver, tighten all screws firmly to the torque specified in the screw information table for each step. • Ensure torque screwdrivers are calibrated correctly following country specifications. Retaining serial numbers This topic provides instructions on the following: • "Restoring the serial number of the system unit" on page 48 • "Retaining the UUID" on page 49 • "Reading or writing the ECA information" on page 49 Restoring the serial number of the system unit When the computer was manufactured, the EEPROM on the system board was loaded with the serial numbers of the system and all major components. These numbers need to remain the same throughout the life of the computer. If you replace the system board, you must restore the serial number of the system board to its original value. Before replacing the system board, save the original serial number by doing the following: 1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the computer. 2. From the main menu, select 1. Set System Identification. 3. Select 2. Read S/N data from EEPROM. The serial number of each device in your computer is displayed. The serial number of the system board is listed is listed as 20: Serial number. Write down that number. Note: The serial number of the system board is also written on the label attached to the bottom of the computer. After you have replaced the system board, restore the serial number by doing the following: 1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later and restart the computer. 2. From the main menu, select 1. Set System Identification. 3. Select 1. Add S/N data from EEPROM. Follow the instructions on the screen. If the MTM and Product ID numbers differ from each other on the rear label, use what is shown for the Product ID field. See example below: 48 Hardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Notes:
•
If you have a torque driver, refer to the
Torque
column in the screw information table for each step.
•
Make sure that you use the correct screw. It is recommended to use new screws for replacements. If
you have a torque screwdriver, tighten all screws firmly to the torque specified in the screw information
table for each step.
•
Ensure torque screwdrivers are calibrated correctly following country specifications.
Retaining serial numbers
This topic provides instructions on the following:
•
“Restoring the serial number of the system unit” on page 48
•
“Retaining the UUID” on page 49
•
“Reading or writing the ECA information” on page 49
Restoring the serial number of the system unit
When the computer was manufactured, the EEPROM on the system board was loaded with the serial
numbers of the system and all major components. These numbers need to remain the same throughout
the life of the computer.
If you replace the system board, you must restore the serial number of the system board to its original value.
Before replacing the system board, save the original serial number by doing the following:
1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the
computer.
2. From the main menu, select
1. Set System Identification
.
3. Select
2. Read S/N data from EEPROM
.
The serial number of each device in your computer is displayed. The serial number of the system board is
listed is listed as
20: Serial number
.
Write down that number.
Note:
The serial number of the system board is also written on the label attached to the bottom of the
computer.
After you have replaced the system board, restore the serial number by doing the following:
1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later and restart the
computer.
2. From the main menu, select
1. Set System Identification
.
3. Select
1. Add S/N data from EEPROM
. Follow the instructions on the screen.
If the MTM and Product ID numbers differ from each other on the rear label, use what is shown for the
Product ID field. See example below:
48
Hardware Maintenance Manual