Lenovo ThinkPad Edge E520 (English) User Guide - Page 154

C:\CONFIG.SYS, C:\WINDOWS\EMM386.EXE RAM, EMM386 Not Installed-Unable to Set Frame Base Address. - fan error

Page 154 highlights

Solution: The daughter card is not supported on this computer. Remove it. • Message: 1805: Unauthorized Wireless USB card is plugged in - Power off and remove the Wireless USB card. Solution: The Wireless USB card is not supported on this computer. Remove it. • Message: 2100: Initialization error on HDD0 (Main HDD). Solution: The hard disk is not working. Have the hard disk serviced. • Message: 2110: Read error on HDD0 (Main HDD). Solution: The hard disk is not working. Have the hard disk serviced. • Message: The power-on password prompt Solution: A power-on password or a supervisor password is set. Type the password and press Enter to use the computer (refer to "Using passwords" on page 59). If the power-on password is not accepted, a supervisor password might have been set. Type the supervisor password and press Enter. If you still see the same error message, have the computer serviced. • Message: The hard disk password prompt Solution: A hard disk password is set. Type the password and press Enter to use the computer (refer to "Hard disk passwords" on page 61). • Message: Hibernation error Solution: The system configuration changed between the time your computer entered hibernation mode and the time it left this mode, and your computer cannot resume normal operation. - Restore the system configuration to what it was before your computer entered hibernation mode. - If the memory size has been changed, re-create the hibernation file. • Message: Operating system not found. Solution: Verify the following: - The hard disk drive is correctly installed. - A startable disc is in the drive. If you still see the same error message, check the boot sequence using ThinkPad Setup. • Message: Fan error Solution: Cooling fan has failed. Have the computer serviced. • Message: EMM386 Not Installed-Unable to Set Page Frame Base Address. Solution: Edit C:\CONFIG.SYS and change a line from device = C:\WINDOWS\EMM386.EXE RAM to device = C:\WINDOWS\EMM386.EXE NOEMS and save this file. • Message: CardBus Configuration Error-Device Disabled. Solution: Press F1 to go to ThinkPad Setup. Press F9 and then press Enter to load the default setting. Press F10 and then press Enter to restart the system. • Message: Thermal sensing error Solution: The thermal sensor is not functioning correctly. Have the computer serviced. • Message: Cannot boot from any device. 136 User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194

Solution
: The daughter card is not supported on this computer. Remove it.
Message
: 1805: Unauthorized Wireless USB card is plugged in - Power off and remove the Wireless
USB card.
Solution
: The Wireless USB card is not supported on this computer. Remove it.
Message
: 2100: Initialization error on HDD0 (Main HDD).
Solution
: The hard disk is not working. Have the hard disk serviced.
Message
: 2110: Read error on HDD0 (Main HDD).
Solution
: The hard disk is not working. Have the hard disk serviced.
Message
: The power-on password prompt
Solution
: A power-on password or a supervisor password is set. Type the password and press Enter to
use the computer (refer to “Using passwords” on page 59). If the power-on password is not accepted, a
supervisor password might have been set. Type the supervisor password and press Enter. If you still see
the same error message, have the computer serviced.
Message
: The hard disk password prompt
Solution
: A hard disk password is set. Type the password and press Enter to use the computer (refer to
“Hard disk passwords” on page 61).
Message
: Hibernation error
Solution
: The system configuration changed between the time your computer entered hibernation mode
and the time it left this mode, and your computer cannot resume normal operation.
Restore the system configuration to what it was before your computer entered hibernation mode.
If the memory size has been changed, re-create the hibernation file.
Message
: Operating system not found.
Solution
: Verify the following:
The hard disk drive is correctly installed.
A startable disc is in the drive.
If you still see the same error message, check the boot sequence using ThinkPad Setup.
Message
: Fan error
Solution
: Cooling fan has failed. Have the computer serviced.
Message
: EMM386 Not Installed-Unable to Set Page Frame Base Address.
Solution
: Edit
C:\CONFIG.SYS
and change a line from device =
C:\WINDOWS\EMM386.EXE RAM
to device =
C:\WINDOWS\EMM386.EXE NOEMS
and save this file.
Message
: CardBus Configuration Error-Device Disabled.
Solution
: Press F1 to go to ThinkPad Setup. Press F9 and then press Enter to load the default setting.
Press F10 and then press Enter to restart the system.
Message
: Thermal sensing error
Solution
: The thermal sensor is not functioning correctly. Have the computer serviced.
Message
: Cannot boot from any device.
136
User Guide