Lexmark X443 Setup and User's Guide - Page 103

Slide the other end of the new pick roller 2 into the lower bracket hole

Get Lexmark X443 PDF manuals and user guides View all Lexmark X443 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

10 Slide the left bearing toward the retaining sleeve. Note: Be careful not to drop the bearings during this process. The copper bearings fit loosely on the ends of the pick roller and can slip off easily until the pick roller is reinserted into the holding brackets. Retaining sleeve Right bearing Pick roller 2 Left bearing 11 Insert the sleeve end of pick roller 2 into the lower hole of the left holding bracket as far as it goes. Right holding bracket Left holding bracket Lower bracket hole Pick roller 2 12 Slide the other end of the new pick roller 2 into the lower bracket hole of the right holding bracket. Make sure the gears on the pick roller is seated well with the gears of the ADF. 95

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
95
10
Slide the left bearing toward the retaining sleeve.
Note:
Be careful not to drop the bearings during this process. The copper
bearings fit loosely on the ends of the pick roller and can slip off
easily until the pick roller is reinserted into the holding brackets.
11
Insert the sleeve end of pick roller 2 into the lower hole of the left holding
bracket as far as it goes.
12
Slide the other end of the new pick roller 2 into the lower bracket hole of
the right holding bracket. Make sure the gears on the pick roller is seated
well with the gears of the ADF.
Pick roller 2
Right bearing
Left bearing
Retaining sleeve
Lower bracket hole
Pick roller 2
Right holding bracket
Left holding bracket