Lowrance Elite-12 Ti Installation Manual EN - Page 15

Installation, Mounting location, launching, or retrieving of the boat.

Get Lowrance Elite-12 Ti PDF manuals and user guides View all Lowrance Elite-12 Ti manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

3 Installation Mounting location Choose the mounting locations carefully before you drill or cut. The unit should be mounted so that the operator can easily use the controls and clearly see the screen. The unit has a high-contrast screen and is viewable in direct sunlight, but for best results install the unit out of direct sunlight. The chosen location should have minimal glare from windows or bright objects. Ensure that any holes cut are in a safe position and will not weaken the boat's structure. If in doubt, consult a qualified boat builder, or marine electronics installer. Before cutting a hole in a panel, make sure that there are no hidden electrical wires or other parts behind the panel. Check that it is possible to route cables to the intended mounting location. Leave sufficient clearance to connect all relevant cables. Do not mount any part where it can be used as a hand hold, where it might be submerged, or where it will interfere with the operation, launching, or retrieving of the boat. The mounting location may affect the internal GPS receiver. Test the unit in its intended location to ensure satisfactory reception. An external GPS source can be added to overcome poor reception areas. For overall width and height requirements, refer to "Dimensional drawings" on page 64. Good ventilation is required. Choose a location that will not expose the unit to conditions that exceed the specifications - refer to "Technical specifications" on page 62. Installation | ELITE Ti Installation Manual 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Installation
Mounting location
Choose the mounting locations carefully before you drill or cut. The
unit should be mounted so that the operator can easily use the
controls and clearly see the screen.
The unit has a high-contrast screen and is viewable in direct
sunlight, but for best results install the unit out of direct sunlight.
The chosen location should have minimal glare from windows or
bright objects.
Ensure that any holes cut are in a safe position and will not weaken
the boat’s structure. If in doubt, consult a qualified boat builder, or
marine electronics installer.
Before cutting a hole in a panel, make sure that there are no hidden
electrical wires or other parts behind the panel.
Check that it is possible to route cables to the intended mounting
location.
Leave sufficient clearance to connect all relevant cables.
Do not mount any part where it can be used as a hand hold, where
it might be submerged, or where it will interfere with the operation,
launching, or retrieving of the boat.
The mounting location may affect the internal GPS receiver. Test the
unit in its intended location to ensure satisfactory reception. An
external GPS source can be added to overcome poor reception
areas.
For overall width and height requirements, refer to
"Dimensional
drawings"
on page 64.
Good ventilation is required. Choose a location that will not expose
the unit to conditions that exceed the specifications - refer to
"Technical specifications"
on page 62.
3
Installation
| ELITE Ti Installation Manual
15