Lowrance Elite-12 Ti Installation Manual EN - Page 51

Software upgrades, NMEA 2000 device upgrades, Upgrade, This Display

Get Lowrance Elite-12 Ti PDF manuals and user guides View all Lowrance Elite-12 Ti manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

The unit may be used to apply software updates to itself, and to supported network devices, with files read off a memory card inserted in the card reader. Before initiating an update to the unit itself, be sure to back up any potentially valuable user data. Software upgrades The update file must be loaded to the root directory of the memory card. The update may be initiated at boot up: insert the memory card into the card reader before turning the unit on, boot the unit, and follow the on-screen instructions. Alternatively, in the Files menu, locate the update file on the memory card inserted in the card reader and select Upgrade, followed by This Display. Accept the prompt to reboot the unit, and wait a few moments as the unit restarts. Do not remove the memory card or repower the unit until the process is completed (this typically takes no more than a couple of minutes). NMEA 2000 device upgrades NMEA 2000 is not available on the ELITE-5Ti. The update file must be loaded to the root directory of a memory card inserted in the card reader. 1. Select the Files toolbar option and select the update file under Memory card. 2. Select the Upgrade option presented when the file is highlighted. A list should appear displaying any compatible devices the update file applies to. In most cases this will be a single device. Ú Note: If no device is shown, check that the device to be updated has power, and run any outstanding updates for the unit first. 3. Select the device and initiate the upgrade. Do not interrupt the upgrade process. Software Setup | ELITE Ti Installation Manual 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
The unit may be used to apply software updates to itself, and to
supported network devices, with files read off a memory card
inserted in the card reader.
Before initiating an update to the unit itself, be sure to back up any
potentially valuable user data.
Software upgrades
The update file must be loaded to the root directory of the memory
card.
The update may be initiated at boot up: insert the memory card into
the card reader before turning the unit on, boot the unit, and follow
the on-screen instructions.
Alternatively, in the Files menu, locate the update file on the
memory card inserted in the card reader and select
Upgrade
,
followed by
This Display
. Accept the prompt to reboot the unit,
and wait a few moments as the unit restarts. Do not remove the
memory card or repower the unit until the process is completed
(this typically takes no more than a couple of minutes).
NMEA 2000 device upgrades
NMEA 2000 is not available on the ELITE-5Ti.
The update file must be loaded to the root directory of a memory
card inserted in the card reader.
1.
Select the Files toolbar option and select the update file under
Memory card.
2.
Select the Upgrade option presented when the file is
highlighted. A list should appear displaying any compatible
devices the update file applies to. In most cases this will be a
single device.
Ú
Note:
If no device is shown, check that the device to be
updated has power, and run any outstanding updates for the
unit first.
3.
Select the device and initiate the upgrade. Do not interrupt the
upgrade process.
Software Setup
| ELITE Ti Installation Manual
51