Lowrance HDS-5 Gen2 Operation Manual - Page 103

Units

Get Lowrance HDS-5 Gen2 PDF manuals and user guides View all Lowrance HDS-5 Gen2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

Settings To silence an alarm: When an Alarm is triggered, a tone will sound and a alarm window will appear on the screen. Press Enter to silence the alarm and close the alarm window. After alarm is silenced its corresponding alarm bell will continue to flash in the bottom left corner of the screen. To remove the bell from the screen, disable the alarm and then enable it again. The bell will not reappear unless the alarm is triggered. Set Limit Sets thresholds (limits) that will trigger the alarm when met or exceeded. If a threshold can be set for a particular alarm, the Set Limit button will appear at the bottom of the screen when that alarm is highlighted on the alarm list. To set alarm limit: 1. Highlight the desired alarm on the alarm screen and press Menu. 2. Select Set Limit and press enter. The Alarm Limit keypad will appear. 3. Input the desired alarm threshold and press enter. Siren Enabled When the Siren is enabled, a tone will sound when an alarm is triggered. To enable sirens, highlight Siren Enabled on the Alarms menu and press ENTER. Units Controls the unit of measure used for unit data. Only Imperial and Nautical units will be shown if the unit is operated outside of a zone defined by 30 degrees west longitude and the International Date Line. To access the Units menu, select Units from the Settings menu and press enter. To change a unit of measure: 1. Select a unit from the Units menu. Press enter. 2. Select the a unit of measure and press enter. 101

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
101
Settings
To silence an alarm:
When an Alarm is triggered, a tone will sound and a alarm window will appear on
the screen. Press
ENTER
to silence the alarm and close the alarm window.
After alarm is silenced its corresponding alarm bell will continue to flash
in the bottom left corner of the screen. To remove the bell from the screen,
disable the alarm and then enable it again. The bell will not reappear unless
the alarm is triggered.
Set Limit
Sets thresholds (limits) that will trigger the alarm when met or exceeded. If a
threshold can be set for a particular alarm, the Set Limit button will appear at the
bottom of the screen when that alarm is highlighted on the alarm list.
To set alarm limit:
1.
Highlight the desired alarm on the alarm
screen and press
MENU
.
2. Select
Set Limit
and press
ENTER
. The
Alarm Limit keypad will appear.
3.
Input the desired alarm threshold and
press
ENTER
.
Siren Enabled
When the Siren is enabled, a tone will sound when an alarm is triggered. To enable
sirens, highlight
Siren Enabled
on the Alarms menu and press
ENTER
.
Units
Controls the unit of measure used for
unit data. Only Imperial and Nautical units
will be shown if the unit is operated outside of a zone defined by 30 degrees west
longitude and the International Date Line.
To access the Units menu, select
Units
from the Settings menu
and press
ENTER
.
To change a unit of measure:
1.
Select a unit from the Units menu. Press
ENTER
.
2.
Select the a unit of measure and press
ENTER
.