MSI MEG Z390 GODLIKE User Manual - Page 46

T_SEN1~2: Thermal Sensor Connectors, JSLOW1: Slow Mode Booting Jumper

Get MSI MEG Z390 GODLIKE PDF manuals and user guides View all MSI MEG Z390 GODLIKE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

T_SEN1~2: Thermal Sensor Connectors These connectors allow you to connect the thermistor cable and use it to monitor the temperature of the detection point. Sense GND Thermistor cable JSLOW1: Slow Mode Booting Jumper This jumper is used for LN2 cooling solution, that provides the extreme overclocking conditions, to boot at a stable processor frequency and to prevent the system from crashing. Normal (default) Enabled (Please enable this jumper during BIOS POST.) Important y Users will try extreme low temperature (must be higher than -124 degrees to prevent Debug Code 00) overclocking at their own risks. y The overclocking results will vary according to the CPU version. y Please don't set to Enabled when the system is powered off or can't be started. 46 Overview of Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
46
Overview of Components
JSLOW1: Slow Mode Booting Jumper
This jumper is used for LN2 cooling solution, that provides the extreme overclocking
conditions, to boot at a stable processor frequency and to prevent the system from
crashing.
Normal
(default)
Enabled
(Please enable this jumper
during BIOS POST.)
Important
y
Users will try extreme low temperature (must be higher than -124 degrees to prevent
Debug Code 00) overclocking at their own risks.
y
The overclocking results will vary according to the CPU version.
y
Please don’t set to
Enabled
when the system is powered off or can
’
t be started.
T_SEN1~2: Thermal Sensor Connectors
These connectors allow you to connect the thermistor cable and use it to monitor the
temperature of the detection point.
Thermistor cable
GND
Sense