Marantz SR9600 SR9600 User Guide - Page 30

ENGLISH CONNECTING i.LINK COMPONENTS The SR9600 connects to i.LINK components that support up to S400 (400 Mbps). Use a 4-pin i.LINK cable that supports S400 for i.LINK connections with this receiver. Video data cannot be transmitted via the i.LINK (Audio) supported by this receiver. To connect to a video component, connect the video signal separately. When connected to other Marantz products using i.LINK, the system can be operated over the i.LINK cable. When multiple i.LINK components are connected to the receiver, data can be transmitted through the other i.LINK components. The components do not have to be connected in a specific order to do this. (see page 34) i.LINK does not distinguish between input and output terminals in two-way communications. Input and output are switched according to the direction in which signals flow. i.LINK (AUDIO) DIGITAL IN (AUDIO) 1 S400 2 3 S400 4 7.1CH IN MAIN IN L SL SBL C L R SL SR SBL SBR C MULTI OUT A B L R SR (AUX 2) L AUDIO R SBR SW PRE OUT SW AUDIO R SPEAKER C ON OFF IN TAPE OUT IN CD-R/MD OUT CD CENTER SURR.BACK /MULTI SPK. /SPK. C LEFT SURR.BACK /MULTI SPK. /SPK. C RIGHT FRONT A LEFT FRONT A RIGHT FRONT B LEFT DVD LD TV DSS VCR-1 VCR-2 / DVD-R MONITOR OUT IN OUT IN OUT 1 2 5 VIDEO 6 MULTI OUT A B S-VIDEO 7 HDMI 8 Ver 1.1 INPUT-1 (DVD) INPUT-2 (DSS) OUTPUT VIDEO Y CB/PB CR/PR OUTPUT-1 INPUT-1 (DVD) INPUT-2 (DSS) INPUT-3 (VCR-1) INPUT-4 (VCR-2 / DVD-R) AM TUNER-1 GND FM(75Ω) AM TUNER-2 GND FM(75Ω) CLASS 2 WIRING FRONT B RIGHT SURR. LEFT SURR. RIGHT COMPONENT OPT VIDEO Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR OUTPUT-2 SWITCHED 1A 120W MAX SPEAKER SYSTEMS FRONT A OR B, CENTER, SURR, SURR BACK : MINIMUM 6 OHMS FRONT A AND B : MINIMUM 8 OHMS COAX 1 3 1 3 IR FLASHER RECEIVER IN IN IN MODEL NO. SR9600 UNSWITCHED 1A 120W MAX AC IN DIGITAL OUT USB AUDIO RS232C 2 4 2 4 DC OUT EMITTER OUT OUT RC-5 MULTI RC AC 120V 60HZ AC OUTLETS Example connection : Up to 17 devices can be connected in a daisy chain. The SR9600 can detect up to 15 components. i.LINK component i.LINK component i.LINK component Example connection : Up to 63 devices can be connected in a tree formation by branching. This kind of connection is possible with devices that have 3 or more i.LINK connectors. i.LINK component i.LINK component i.LINK component Bad connection example: i.LINK component i.LINK component i.LINK component i.LINK component i.LINK component i.LINK component Do not connect devices in a loop as shown in the figure. Notes: • The i.LINK feature of the SR9600 supports only devices (digital broadcast receiver (MPEG-2 TS), digital video (DV), etc.) that support i.LINK (Audio). Do not connect unsupported devices because malfunctions can occur. • During playback of an i.LINK device, do not disconnect or connect the i.LINK cable of other devices. Also, do not connect new devices or turn the power on/off. This can cut off the sound. • Some i.LINK devices cannot relay data while power is off or the device is on standby. See the instruction manual of the connected device. The SR9600 does not relay data in this state either. • The maximum data transfer speed of an i.LINK device is labeled near to its i.LINK connector. This maximum data speed is standardized as S100 (100 Mbps), S200 (200 Mbps) and S400 (400 Mbps). The SR9600 has a maximum data transfer speed of S400, but if the connected device supports only S100 or S200, the actual data transfer may be slower than 400 Mbps. Mbps stands for "mega bits per second". It expresses the quantity of data that can be sent in 1 second. The SR9600 supports S400, therefore it sends 400 Mb of data every second. • The i.LINK feature does not assure the connection and operation of all i.LINK devices. Whether data and control signals can be exchanged between i.LINK devices or not will depend on the functions of each device. • Carefully check the configuration of the i.LINK connector before connecting an i.LINK cable. Forcing the cable into the connector in the wrong orientation can damage the connector. • Do not connect an i.LINK cable with power to the SR9600 on. • Use an i.LINK cable that is no longer than 3.5 m and that supports S400. • Some players require i.LINK setup. For details, see the instruction manual of the device. * Some devices may require you to make settings with the device connected to the SR9600 during the setup. • Audio signals input from the i.LINK connector are not output from the DIGITAL OUT jacks. • With some source devices, it takes time before sound is produced. This time is needed to detect the status of both the device and the SR9600. The amount of time will differ according to the connected player. 28 Once the devices have been connected, activate power to the SR9600 and components, and make the settings as explained in "i.LINK SETUP" (see page 34). The i.LINK feature works as a temporary input source unless the settings are made. (See page 48)