Marantz SR9600 SR9600 User Guide - Page 31

ERROR MESSAGES FOR CONNECTED i.LINK DEVICES "LOOP CONNECT" This message is displayed if the i.LINK device is connected in a loop. Connect the device so that the connection does not form a loop. "NODE OVER" This message is displayed if more than 63 i.LINK devices are connected to the SR9600, including the SR9600. Limit connections to 63 a maximum devices including the SR9600. "HOP OVER" This message is displayed if more than 17 i.LINK devices are connected in a daisy chain. Keep daisy chain connections to a maximum 17 devices. "BUS FULL" This message is displayed if too many devices are outputting signals on the i.LINK bus. Either shut off power or disconnect unused devices. "CANNOT LINK" This message is displayed if the SR9600 cannot connect to an i.LINK device or if an unconnected device is selected as the input source. Disconnect and reconnect the i.LINK cable, or shut power to the SR9600 off and turn it back on. MESSAGES WHEN AN i.LINK DEVICE IS CONNECTED "LINK CHECK" This message is displayed while the SR9600 checks for changes in i.LINK device connections. "NO SIGNAL" This message is displayed if a signal not supported by the SR9600 is input. CONNECTING OTHER EQUIPMENT DIGITAL IN (AUDIO) 1 S400 2 3 S400 4 7.1CH IN MAIN IN L SL SBL C L R SL SR SBL SBR C MULTI OUT A B L R SR (AUX 2) L AUDIO R SBR SW PRE OUT SW AUDIO R SPEAKER C ON OFF IN TAPE OUT IN CD-R/MD OUT CD CENTER SURR.BACK /MULTI SPK. /SPK. C LEFT SURR.BACK /MULTI SPK. /SPK. C RIGHT FRONT A LEFT FRONT A RIGHT FRONT B LEFT DVD LD TV DSS VCR-1 VCR-2 / DVD-R MONITOR OUT IN OUT IN OUT 1 2 5 VIDEO 6 MULTI OUT A B S-VIDEO 7 HDMI 8 Ver 1.1 INPUT-1 (DVD) INPUT-2 (DSS) OUTPUT VIDEO Y CB/PB CR/PR OUTPUT-1 INPUT-1 (DVD) INPUT-2 (DSS) INPUT-3 (VCR-1) INPUT-4 (VCR-2 / DVD-R) AM TUNER-1 GND FM(75Ω) AM TUNER-2 GND FM(75Ω) CLASS 2 WIRING FRONT B RIGHT SURR. LEFT SURR. RIGHT COMPONENT OPT VIDEO Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR OUTPUT-2 SWITCHED 1A 120W MAX SPEAKER SYSTEMS FRONT A OR B, CENTER, SURR, SURR BACK : MINIMUM 6 OHMS FRONT A AND B : MINIMUM 8 OHMS COAX 1 3 1 3 IR FLASHER RECEIVER IN IN IN MODEL NO. SR9600 UNSWITCHED 1A 120W MAX AC IN DIGITAL OUT USB AUDIO RS232C 2 4 2 4 DC OUT EMITTER OUT OUT RC-5 MULTI RC AC 120V 60HZ AC OUTLETS RS232C 1 3 1 3 2 4 2 4 IR FLASHER RECEIVER IN IN DC OUT EMITTER OUT RS232C Connect an external control device or other device for servicing. (Use a straight cable for the connection.) IR RECEIVER IN This receiver can be operated by remote control without using the internal IR receiver, by connecting an external IR receiver. DC OUT (DC TRIGGER) External devices can be controlled from the SR9600 by connecting them to the DC OUT terminal (12 V). +12V GND Signal EMITTER OUT Outputs the remote control signal input to the IR RECEIVER IN terminals. External components can be controlled by connecting them to the EMITTER OUT terminal. FLASHER IN This receiver can be controlled by connecting a control box or other control device to this receiver. An IR receiver is connected as shown above. Caution: Wrongly connecting an IR receiver or connecting an IR receiver of the wrong voltage can damage the SR9600, therefore do not do this. 29 ENGLISH