Marantz VP-15S1 VP-15S1 User Manual - Page 10
Important Safeguards - lamp
View all Marantz VP-15S1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
ENGLISH IMPORTANT SAFEGUARDS Caution Concerning the Lamp Replacement There is potential glass particle hazard if the lamp ruptures. Caution Concerning the Setup of the Projector For minimal servicing and to maintain high image quality, avoid humidity, dust and cigarette smoke. When the projector is subjected to these environments,the lens and part of ventilation holes must be cleaned more often than usual. As long as the projector is properly maintained in this manner, use in these environments will not reduce the overall operation life. Please note that all internal cleaning must be performed by an Marantz Authorized Dealer, or Service Center. • Do not expose the projector to extreme heat or cold. Operating temperature:41 °F to 95 °F (+5 °C to 35 °C) Storage temperature:-4 °F to 140 °F (-20 °C to +60 °C) Caution Concerning the Lamp Unit There is a potential hazard of glass particle if the lamp ruptures. In case of lamp rupture,contact your nearest Marantz Authorized Dealer or Service Center for a replacement. See "Replacing Lamp Unit". ( P.31) 95˚F (+35˚C) 41˚F (+5˚C) WARNING THIS COVER IS PROVIDED WITH INTERLOCK TO REDUCE THE RISK OF EXCESSIVE ULTRAVIOLET RADIATION. DO NOT DEFEAT ITS PORPOSE OR ATTEMPT TO SERVICE WITHOUT REMOVING COVER COMPLETELY. CAUTION : HIGH PRESSURE LAMP CAUTION HOT : UNPLUG MAY EXPLODED IF IMPROPERLY HANDLED. THE POWER CORD AND WAIT REFER SERVICING TO QUALIFIED SERVICE 60 MINUTES BEFORE CHARGING PERSONNEL. THE LAMP. MODEL NO. VP-16S1 / U1M AC 120V 60HZ 2.0A ATTENTION : LA LAMPE SOUS HAUTE PRESSION PEUT SI ELLE, N'EST PAS MANIPULEE CORRECTEMENT, CONFIER L'OPERATION A UN PERSONNEL D'ENTRETIEN QUALIFIE. ATTENTION CHAUD : DEBRANCER LE CORD ON D'ALOMENTION ET ATENDER 60 MINUTES AVANT DE CHANGER LAMPE. SERIAL NO. Notes on Operation For USA WARNING THIS COVER IS PROVIDED WITH INTERLOCK TO REDUCE THE RISK OF EXCESSIVE ULTRAVIOLET RADIATION. DO NOT DEFEAT ITS PORPOSE OR ATTEMPT TO SERVICE WITHOUT REMOVING COVER COMPLETELY. For Europe CAUTION HOT UNPLUG THE POWER CORD AND WAIT 60 MINUTES BEFORE CHANGING THE LAMP. ATTENTION CHAUD DEBRANCER LE CORD ON D'ALIMENTION ET ATENDER 60 MINUTES AVANT DE CHANGER LAMPE. WARNUNG HEISS ZIEHEN SIE DEN NETZSTECKER AB UND WARTEN SIE 60 MINUTEN, BEVOR SIE DIE GLUHLAMPE WECHSELN. For USA CAUTION : HIGH PRESSURE LAMP CAUTION HOT : UNPLUG MAY EXPLODED IF IMPROPERLY HANDLED. THE POWER CORD AND WAIT REFER SERVICING TO QUALIFIED SERVICE 60 MINUTES BEFORE CHARGING PERSONNEL. THE LAMP. ATTENTION : LA LAMPE SOUS HAUTE PRESSION PEUT SI ELLE, N'EST PAS MANIPULEE CORRECTEMENT, CONFIER L'OPERATION A UN PERSONNEL D'ENTRETIEN QUALIFIE. ATTENTION CHAUD : DEBRANCER LE CORD ON D'ALOMENTION ET ATENDER 60 MINUTES AVANT DE CHANGER LAMPE. • The exhaust ventilative hole, the lamp cage cover and adjacent areas may get extremely hot during projector operation. To prevent injury,do not touch these areas until they have sufficiently cooled down. • Allow at least 1 foot (30 cm)of space between the exhaust ventilative hole and the nearest wall or obstruction. MODEL NO•. VIf Pth-e1c2oSol1in/gNfa1nSbecomes obstructed, a protection device will automatically turn off the projector lamp. AC 120V 6T0hHisZdoe2s.0noWt indicate a malfunction. Remove the projector power cord from the wall outlet and wait at least 10 minutes. SERIAL NO. Then turn on the power by plugging the power cord back in. This will return the projector to the normal operating condition. MADE IN JAPAN FABRIQUE AU JAPON For Europe CAUTION VORSICHT : HIGH PRESSURE LAMP MAY EXPLODED IF BEI FALSCHER HANDHABUNG M IMPROPERLY HANDLED. REFER SERVICING KANN DIE HOCHDRUCKLAMPE TO QUALIFIED SERVICE PERSONNEL. EXPLODIEREN UBERLASSEN ATTENTION LA LAMPE SOUS HAUTE PRESSION PEUT SIE WARTUNGSARBEITEN NUR FACHPERSONAL. EXPLOSER SI ELLE, N'EST PAS MANIPULEE CORRECTEMENT, CONFIER L'OPERATION A UN PERSONNEL D'ENTRETIEN QUALIFIE. 2