Marantz VP-15S1 VP-15S1 User Manual - Page 39

MAINTENANCE Lamp Life and Replace Lamp ❖ Lamp Life Display the remaining lamp life by pressing the INFO. button on the remote controller. Information Video Input Picture Mode Gamma Aspect Lamp Mode Iris Lamp Life Total Time Component 1 - 1080i / 60 User 1 A Normal Economy 1 921 Hours 3653 Hours ENTER INPUT A ASPECT I INFO. CINEMA VCR MODE BLACK LEVEL PATTERN BLACK Notes: • The maximum life limit of the lamp is 2000 hours. Although we care very much about quality, the lamp can rarely breaks down if running time exceeds 1000 hours. Therefore we recommend to replace the lamp if Lamp Life gets under 1000 hours. The lamp cannot be used exceeding the maximum life limit. • This product is checked under strict quality control when it is shipped out form factory. "Total Hours" in the menu includes the time for this check. So "Total Hours" may not be 0 hours when it is used first time. - When the lamp life becomes less than 100 hours and the unit is still on, the remaining lamp life is displayed on the screen automatically. Warning Lamp Life 100 Hours - When the lamp life becomes less than 5 hours, the remaining lamp life is displayed on the screen . Warning Lamp Life 5 Hours A1 A2 RGB G3 THTR STD DYN G4 BLANKING B1 B2 B3 OFF V-MUTE MENU M ENTER INPUT A I To clear the warning, press the MENU button. - Approximately 2 minutes after the lamp reaches the end of its lamp life, power to the projector shuts OFF and the WARNING indicator lights up a yellow color. If the below message appears on the screen and power shuts OFF soon thereafter, promptly replace the lamp with a new one. (See "Replacing Lamp Unit" P.31) Warning Lamp Life 0 Hours ❖ Initialize the Lamp Life The lamp has a lamp life of 2000 hours. The projector is designed to shut OFF power if the lamp is used beyond this 2000 hours lamp life. In such case, replace the lamp and reset the lamp life counter as follows. 1. After the message "Lamp Life 0 Hours" appears, power to the projector shuts OFF. Promptly replace the lamp with a new one. ( P.31 "Replacing Lamp Unit") 2. Once the lamp has been replaced, press the ON button on the remote control or the / I button on the projector. The below message appears on the screen for 120 seconds. New Lamp ? Yes No 3. Select "Yes", using the 1 / 2 buttons. 4. Press the ENTER button. The lamp life indicator is now initialized. 3. 4. 2. STANDBY ON IRIS LAMP C.TEMP GAMMA COMP.1 COMP.2 S-VIDEO USER C1 C2 S G1 HDMI 1 HDMI 2 VIDEO H1 H2 V G2 AUX 1 AUX 2 A1 A2 RGB G3 THTR STD DYN G4 BLANKING B1 B2 B3 OFF V-MUTE MENU M ENTER INPUT A ASPECT I INFO. CINEMA VCR MODE BLACK LEVEL PATTERN BLACK 2. 4. 3. Replacing Lamp Unit CAUTION: • Do not touch the lamp and the lamp unit carelessly. It is extremely hot. Wait at least one hour for the lamp to cool down before handling. • Do not loosen any screws except for those mentioned below. • The lamp may break if handled improperly. • Do not use other than a Marantz replacement lamp unit. ❖ How to replace the Lamp Unit PREPARATION: When replacing the lamp, turn off the power for the projector. After the cooling fan stops, disconnect the power cord and wait for one hour until the lamp is cooled down completely, then replace the lamp. 1. Press the STANDBY button on the remote controller or the / I button on the projector to turn the projector off. STANDBY ON IRIS LAMP C.TEMP GAMMA COMP.1 COMP.2 S-VIDEO USER C1 C2 S G1 HDMI 1 HDMI 2 VIDEO H1 H2 V G2 AUX 1 AUX 2 A1 A2 RGB G3 2. After the cooling fan stops, Unplug the AC power cord. 31 ENGLISH