Marantz VP-15S1 VP-15S1 User Manual - Page 40

ENGLISH 3. Wait at the least one hour for the lamp and 5. Remove the lamp cover screw. lamp unit to cool down. 4. Read the caution and warning labels on the unit. Lamp cover 8. Holding the handle and pull the lamp unit out 11. Install the lamp cover back in its original toward your side. position and fasten with the fastening screw. (a) Lamp unit A A WARNING THIS COVER IS PROVIDED WITH INTERLOCK TO REDUCE THE RISK OF EXCESSIVE ULTRAVIOLET RADIATION. DO NOT DEFEAT ITS PORPOSE OR ATTEMPT TO SERVICE WITHOUT REMOVING COVER COMPLETELY. CAUTION : HIGH PRESSURE LAMP CAUTION HOT : UNPLUG MAY EXPLODED IF IMPROPERLY HANDLED. THE POWER CORD AND WAIT REFER SERVICING TO QUALIFIED SERVICE 60 MINUTES BEFORE CHARGING PERSONNEL. THE LAMP. ATTENTION : LA LAMPE SOUS HAUTE PRESSION PEUT SI ELLE, N'EST PAS MANIPULEE CORRECTEMENT, CONFIER L'OPERATION A UN PERSONNEL D'ENTRETIEN QUALIFIE. ATTENTION CHAUD : DEBRANCER LE CORD ON D'ALOMENTION ET ATENDER 60 MINUTES AVANT DE CHANGER LAMPE. SERIAL NO. B For USA WARNING THIS COVER IS PROVIDED WITH INTERLOCK TO REDUCE THE RISK OF EXCESSIVE ULTRAVIOLET RADIATION. DO NOT DEFEAT ITS PORPOSE OR ATTEMPT TO SERVICE WITHOUT REMOVING COVER COMPLETELY. For Europe CAUTION HOT UNPLUG THE POWER CORD AND WAIT 60 MINUTES BEFORE CHANGING THE LAMP. ATTENTION CHAUD DEBRANCER LE CORD ON D'ALIMENTION ET ATENDER 60 MINUTES AVANT DE CHANGER LAMPE. WARNUNG HEISS ZIEHEN SIE DEN NETZSTECKER AB UND WARTEN SIE 60 MINUTEN, BEVOR SIE DIE GLUHLAMPE WECHSELN. 6. Remove the lamp cover in the direction of the arrow. Lamp cover B For USA CAUTION : HIGH PRESSURE LAMP CAUTION HOT : UNPLUG MAY EXPLODED IF IMPROPERLY HANDLED. THE POWER CORD AND WAIT REFER SERVICING TO QUALIFIED SERVICE 60 MINUTES BEFORE CHARGING PERSONNEL. THE LAMP. ATTENTION : LA LAMPE SOUS HAUTE PRESSION PEUT SI ELLE, N'EST PAS MANIPULEE CORRECTEMENT, CONFIER L'OPERATION A UN PERSONNEL D'ENTRETIEN QUALIFIE. ATTENTION CHAUD : DEBRANCER LE CORD ON D'ALOMENTION ET ATENDER 60 MINUTES AVANT DE CHANGER LAMPE. 7. Open the cover sheet and remove the two screws (slotted head screwdriver required) MODEL NO. tVhPa-t1l2oSck1/dNo1wSn the lamp unit. Do not remove AC 120V 6a0nHyZoth2e.0rWscrews. SERIAL NO. Cover sheet MADE IN JAPAN FABRIQUE AU JAPON 9. Install a new lamp unit in position securely. 10. Lock the lamp unit in place with the two screws removed in step 7. Press on the handle until it folds over and close the cover sheet. (b) 12. Plug in the video projector and turn on the power and project the image. • If the lamp is replaced before reaching its 2000 hours lamp life, see "Reset Lamp Life" ( P.30). • If the lamp is replaced after reaching its 2000 hours lamp life, see "Initialize the Lamp Life" ( P.31). For Europe CAUTION VORSICHT : HIGH PRESSURE LAMP MAY EXPLODED IF BEI FALSCHER HANDHABUNG M IMPROPERLY HANDLED. REFER SERVICING KANN DIE HOCHDRUCKLAMPE TO QUALIFIED SERVICE PERSONNEL. EXPLODIEREN UBERLASSEN ATTENTION LA LAMPE SOUS HAUTE PRESSION PEUT SIE WARTUNGSARBEITEN NUR FACHPERSONAL. EXPLOSER SI ELLE, N'EST PAS MANIPULEE CORRECTEMENT, CONFIER L'OPERATION A UN PERSONNEL D'ENTRETIEN QUALIFIE. 32