Maytag MMMF8030PZ Owners Manual - Page 20

Rotate Blower Motor for Roof Venting Installation, Electrical Shock Hazard

Get Maytag MMMF8030PZ PDF manuals and user guides View all Maytag MMMF8030PZ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

11. Check to make sure the 2 screws are secured properly in the blower motor screw holes, so that the motor cannot move. WARNING B A B A. Screws B. Blower motor screw holes 12. Return the damper plate to its original horizontal position. A Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. 14. Plug in the microwave oven. Check if the vent fan runs with abnormal sounds, go back through the steps to see which step was skipped. Rotate Blower Motor for Roof Venting Installation 1. Repeat Steps 1 to 5 from "Wall Venting Installation Only." 2. Using diagonal wire cutting pliers, gently snip out the rectangular vent covers on the damper plate at the perforations. A A. Damper plate 13. Secure damper plate with 2 screws removed in Step 1. A B A. Damper plate B. Screw B A. Rectangular vent covers B. Diagonal wire cutting pliers 3. Lower blower motor back into microwave oven. Exhaust ports face the top of microwave oven. A A. Exhaust port IMPORTANT: If blower motor is not positioned with flat side facing the back of the microwave oven (as shown), performance will be poor. 4. Reconnect the blower motor wire into the connector. 5. Reattach the 2 blower screws into the recessed holes in the back of the microwave. 6. Check to make sure the 2 screws are secured properly in the blower motor screw holes, so that the motor cannot move. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
20
11.
Check to make sure the 2 screws are secured properly in the
blower motor screw holes, so that the motor cannot move.
A
B
B
A.
Screws
B.
Blower motor screw holes
12.
Return the damper plate to its original horizontal position.
A
A.
Damper plate
13.
Secure damper plate with 2 screws removed in Step 1.
A
B
A.
Damper plate
B.
Screw
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
14.
Plug in the microwave oven. Check if the vent fan runs with
abnormal sounds, go back through the steps to see which
step was skipped.
Rotate Blower Motor for Roof Venting Installation
1.
Repeat Steps 1 to 5 from “Wall Venting Installation Only.”
2.
Using diagonal wire cutting pliers, gently snip out the
rectangular vent covers on the damper plate at the
perforations.
B
A
A.
Rectangular vent covers
B.
Diagonal wire cutting pliers
3.
Lower blower motor back into microwave oven. Exhaust ports
face the top of microwave oven.
A
A.
Exhaust port
IMPORTANT:
If blower motor is not positioned with flat side
facing the back of the microwave oven (as shown),
performance will be poor.
4.
Reconnect the blower motor wire into the connector.
5.
Reattach the 2 blower screws into the recessed holes in the
back of the microwave.
6.
Check to make sure the 2 screws are secured properly in the
blower motor screw holes, so that the motor cannot move.