Metabo RFEV 19-125 RT Operating Instructions - Page 10
Original instructions
![]() |
View all Metabo RFEV 19-125 RT manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
en ENGLISH Original instructions 1. Declaration of Conformity Under our sole responsibility, we hereby declare that these renovation routers, identified by type and serial number *1), comply with all relevant requirements of the directives *2) and standards *3) and technical documents for *4) - see Page 3. 2. Specified Use When fitted with original Metabo accessories, the machine is suitable for the following tasks: ... Removing plaster, old tile adhesive and paintwork, ... Milling off formwork transitions, ... Roughing concrete surfaces Also suitable for grinding surfaces with diamond cup wheels Do not use for abrasive cutting-off operations, roughing work, sanding, polishing or flap disc work. The machine must not be used with water. It is suitable for commercial use in trade and industry. Always use a suitable dust extraction system: Connect an M-class vacuum cleaner to the extractor connection piece (8). The user bears sole responsibility for any damage caused by improper use. Generally accepted accident prevention regulations and the enclosed safety information must be observed. 3. General safety instructions For your own protection and for the protection of your power tool, pay attention to all parts of the text that are marked with this symbol! WARNING - Reading the operating instructions will reduce the risk of injury. WARNING Read all safety warnings and instructions. Failure to follow all safety warnings and instructions may result in electric shock, fire and/or serious injury. Keep all safety instructions and information for future reference. Pass on your electrical tool only together with these documents. 4. Special Safety Instructions General safety instructions for routing and grinding: Use a) This power tool is designed for surface routing and grinding. Refer to all safety 10 warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all the instructions may result in electric shock, fire and/or serious injury. b) This power tool is not suitable for polishing or tasks using roughing discs, wire brushes, parting grinder discs and flap discs. Operations for which the power tool was not designed may create a hazard and cause personal injury. c) Do not use accessories which are not specifically designed and recommended by the tool manufacturer. The simple fact that an accessory can be attached to your power tool does not ensure safe operation. d) The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart. e) The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be adequately protected or controlled. f) The arbour size of routing tools, flanges, diamond cup wheels or any other accessory must properly fit the spindle of the power tool. Accessories with arbour holes that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control. g) Do not use a damaged accessory. Before use, always check accessories for splinters or cracks and check grinding wheels for cracks or signs of severe wear and tear. If a power tool or accessory is dropped, inspect for damage or install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time. h) Wear personal protective equipment. Depending on application, use a face shield, safety goggles or safety glasses. As appropriate, wear a dust mask, hearing protectors, gloves and workshop apron capable of stopping small abrasive or workpiece fragments. The eye protection must be capable of stopping flying debris generated by various operations. The dust mask or respirator must be capable of filtering particles generated by your operation. Prolonged exposure to high intensity noise may cause hearing loss. i) Keep bystanders a safe distance away from your work area. Anyone entering the work area must wear personal protective equipment. Fragments of a workpiece or broken accessory may fly into the air and cause injury beyond the immediate area of operation. j) Hold power tool by insulated gripping surfaces only, when performing an operation
![](/manual_guide/products/metabo-rfev-19125-rt-operating-instructions-916fe78/10.png)