Miele W3048 Product Manual - Page 55

Hot and cold water connection, Cold water, This washing machine can be operated

Get Miele W3048 PDF manuals and user guides View all Miele W3048 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Installation The washing machine can be connected to a portable water supply. A non-return valve is not needed unless required by building code. The washing machine has ½" (13 mm) pressure hoses with ¾" (19 mm) female hose thread connections. If there is no water hookup, contact a plumber to install a connection. Make sure that the sealing ring is seated properly on the hose connector. Replace the hose only with a genuine Miele hose, or with a hose able to withstand up to 145 psi (10.000 kPa) pressure. The water valve connector must also be able to withstand 145 psi (10.000 kPa).  The bolted connection is under water pressure. Open the water supply slowly to check for leaks. Adjust the rubber seal and the bolted connection if necessary. Hot and cold water connection This washing machine can be operated with cold water and/or hot water. Markings of water intake hoses Cold water Hot water = Blue stripes = Red stripes  For technical reasons, the washing machine must always be connected to cold water. Cold water - The washing machine must be reprogrammed for operation with cold water only. - Attach the second inlet hose to the back of the washing machine. - In the Cottons washing program, the only possible temperature is Not Heat. To protect the inlet valve, the two filters (one at the pressure hose / valve connection and one at the inlet connection to the solenoid valve) must not be removed. 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Installation
51
The washing machine can be
connected to a portable water supply. A
non-return valve is not needed unless
required by building code.
The washing machine has
½
" (13 mm)
pressure hoses with
¾
" (19 mm) female
hose thread connections. If there is no
water hookup, contact a plumber to
install a connection. Make sure that the
sealing ring is seated properly on the
hose connector.
Replace the hose only with a genuine
Miele hose, or with a hose able to
withstand up to 145 psi (10.000 kPa)
pressure. The water valve connector
must also be able to withstand 145 psi
(10.000 kPa).
The bolted connection is under
water pressure. Open the water
supply slowly to check for leaks.
Adjust the rubber seal and the bolted
connection if necessary.
To protect the inlet valve, the two
filters (one at the pressure hose /
valve connection and one at the inlet
connection to the solenoid valve)
must not be removed.
Hot and cold water connection
This washing machine can be operated
with cold water and/or hot water.
Markings of water intake hoses
Cold water
=
Blue stripes
Hot water
=
Red stripes
For technical reasons, the
washing machine
must
always be
connected to cold water.
Cold water
–
The washing machine must be
reprogrammed for operation with
cold water
only
.
–
Attach the second inlet hose to the
back of the washing machine.
–
In the
Cottons
washing program, the
only possible temperature is
Not Heat
.