NEC LT30 LT30/LT35 UM - Page 33

(5) Correcting Keystone Distortion Manually, Adjusting with buttons on the cabinet

Get NEC LT30 - XGA DLP Projector PDF manuals and user guides
UPC - 050927250361
View all NEC LT30 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

3. Projecting an Image (Basic Operation) ᕥ Correcting Keystone Distortion Manually You can also correct the vertical keystone distortion manually. NOTE: Manual keystone correction is not available when there is no signal received by any input. Adjust the keystone distortion manually in the following cases: • To fine tune Keystone correction even after performing the [Auto Keystone] adjustment. • When the menu setting for [Auto Keystone] is turned off Adjusting with buttons on the cabinet 1. Press the SELECT ̆ or ̄ button with no menus displayed. The slide bar will be displayed for your adjustment. 2. Press the EXIT button. The slide bar will be closed. LAMP STATUS POWER ON/STAND BY SOURCE AUTO ADJ. FOCUS SELECT Adjusting with the remote control 1. Press the MENU button. The menu will be displayed. 2. Use the SELECT ̄ button to select [Setup General] and then press the ENTER button. 3. Select the Keystone function. Use the SELECT ̄ button to select [Keystone]. 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
25
µ
Correcting Keystone Distortion Manually
You can also correct the vertical keystone distortion manually.
NOTE: Manual keystone correction is not available when there is no signal received by any input.
Adjust the keystone distortion manually in the following cases:
•
To fine tune Keystone correction even after performing the [Auto Keystone] adjustment.
•
When the menu setting for [Auto Keystone] is turned off
Adjusting with buttons on the cabinet
3. Projecting an Image (Basic Operation)
1. Press the SELECT
±
or
²
button with no
menus displayed.
The slide bar will be displayed for your adjust-
ment.
2.
Press the EXIT button.
The slide bar will be closed.
Adjusting with the remote control
1.
Press the MENU button.
The menu will be displayed.
LAMP
STATUS
POWER
SOURCE
AUTO ADJ.
FOCUS
ON/STAND BY
SELECT
2. Use the SELECT
²
button to select [Setup -
General] and then press the ENTER button.
3.
Select the Keystone function.
Use the SELECT
²
button to select [Keystone].