NEC LT80 User Manual - Page 22

Installation - projector manual

Get NEC LT80 - SVGA DLP Projector PDF manuals and user guides View all NEC LT80 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

41 Settings for Monitor Mode Number of DIP switch S1 S2 S3 S4 S5 S6 S7 S8 Monitor size 15" multi-scan mode /16"-13" ON ON 17" multi-scan mode /19"-13" ON ON 19" multi-scan mode /21"-13" ON ON 13" fixed mode /640‫ן‬480 ON VGA/SVGA mode ON 16" fixed mode /832‫ן‬624 ON 19" fixed mode /1024‫ן‬768 ON NOTE: For setting other than display modes supported by your Macintosh and LT80, using of the DIP switch may bounce a image slightly or may display nothing. If this happens, set the DIP switch to the 13" fixed mode and then restart your Macintosh. After that, restore to a displayable mode and then restart the Macintosh again. Make sure that LT80 and your Macintosh are connected with the monitor adapter and the supplied signal cable (mini D-Sub 15-pin connector) and then restart your Macintosh. → → → Examples of DIP switch setting 13" fixed mode ON 17" multi-scan mode ON 12345678 12345678 VGA/SVGA mode ON 12345678 NOTE: Refer to your computer's owner's manual for more information about your computer's video output requirements and any special identification or configuring your projector's image and monitor may require. INSTALLATION 42

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
Settings for Monitor Mode
Number of DIP switch
Monitor size
15” multi-scan mode /16”–13”
17” multi-scan mode /19”–13”
19” multi-scan mode /21”–13”
13” fixed mode /640
2
480
VGA/SVGA mode
16” fixed mode /832
2
624
19” fixed mode /1024
2
768
41
INSTALLATION
42
S1
ON
ON
ON
ON
S2
S3
S4
ON
S5
ON
ON
S6
ON
S7
ON
S8
ON
NOTE
: For setting other than display modes supported by your Macintosh and LT80, using of the DIP
switch may bounce a image slightly or may display nothing. If this happens, set the DIP switch to the 13”
fixed mode and then restart your Macintosh. After that, restore to a displayable mode and then restart the
Macintosh again.
Make sure that LT80 and your Macintosh are connected with the monitor adapter and the supplied signal
cable (mini D-Sub 15-pin connector) and then restart your Macintosh.
NOTE
: Refer to your computer's owner's manual for more information about your computer's video
output requirements and any special identification or configuring your projector's image and monitor
may require.
ON
→
1
2
3
4
5
6
7
8
ON
→
1
2
3
4
5
6
7
8
ON
→
1
2
3
4
5
6
7
8
13” fixed mode
17” multi-scan mode
VGA/SVGA mode
Examples of DIP switch setting