Home » Netgear Manuals » Modems » Netgear DG834GUv5 » Manual Viewer

Netgear DG834GUv5 Reference Manual - Page 41

Internet Connection Does Note Require A Login

Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

DG834G Reference Manual Note: Disabling NAT will reboot the router and reset all the DG834G configuration settings to the factory default. Disable NAT only if you plan to install the DG834G in a setting where you will be manually administering the IP address space on the LAN side of the router. Internet Connection Does Note Require A Login 1. If your Internet connection does not require a login, select No and fill in the settings according to the instructions below. 2. Enter your Account Name (may also be called Host Name) and Domain Name. These parameters may be necessary to access your ISP's mail or news servers. 3. Internet IP Address: • Select "Get Dynamically from ISP" if your ISP uses DHCP to assign your IP address. Your ISP will automatically assign these addresses. • Select "Use Static IP Address" if your ISP has assigned you a permanent, fixed (static) IP address. Enter the IP address that your ISP assigned. Also enter the IP Subnet Mask and the Gateway IP Address. The gateway is the ISP's ADSL modem router to which your ADSL modem router will connect. • Select "IP Over ATM (IPoA)" if your ISP uses Classical IP Addresses (RFC1577). Enter the IP address, IP Subnet Mask, and Gateway IP Addresses that your ISP assigned. 4. Domain Name Server (DNS) Address: • Select "Get Dynamically from ISP" if your ISP uses DHCP to assign your IP address. Your ISP will automatically assign this address. • If you know that your ISP does not automatically transmit DNS addresses to the ADSL modem router during login, select "Use these DNS servers" and enter the IP address of your ISP's Primary DNS Server. If a Secondary DNS Server address is available, enter it also. A DNS server is a host on the Internet that translates Internet names (such as www.netgear.com) to numeric IP addresses. Typically your ISP transfers the IP address of one or two DNS servers to your ADSL modem router during login. If the ISP does not transfer an address, you must obtain it from the ISP and enter it manually here. 5. You should only disable NAT if you are sure you do not require it. NAT automatically assigns private IP addresses (192.168.0.x) to LAN connected devices. When NAT is disabled, only standard routing is performed by this router. Classical routing lets you directly manage the IP addresses the DG834G uses. Classical routing should be selected only by experienced users. Connecting the Router to the Internet v3.0, September 2005 3-17

Section	Page
DG834G Reference Manual	1
Product and Publication Details	3
Chapter 1 About This Manual	11
Audience, Scope, Conventions, and Formats	11
How to Print this Manual	12
Chapter 2 Introduction	15
About the ADSL Modem Router	15
Key Features	16
A Powerful, True Firewall	16
802.11 Standards-based Wireless Networking	17
Easy Installation and Management	17
Protocol Support	18
Virtual Private Networking (VPN)	19
Auto Sensing and Auto Uplink™ LAN Ethernet Connections	19
Content Filtering	20
Trend Micro Home Network Security	20
What’s in the Box?	21
The Router’s Front Panel	22
The Router’s Rear Panel	23
Chapter 3 Connecting the Router to the Internet	25
What You Need Before You Begin	25
Internet Configuration Requirements	25
Two Setup Methods: 1) Smart Wizard Setup 2) Manual Setup	26
Smart Wizard Setup	26
Manual Setup	27
Understanding ADSL Microfilters	27
ADSL Microfilter	27
ADSL Microfilter with Built-In Splitter	28
Computers Set to DHCP	28
Manually Setting Up Your ADSL Modem Router	28
Auto-Detecting Your Internet Connection Type	34
Wizard-Detected PPPoE Login Account Setup	34
Wizard-Detected PPPoA Login Account Setup	34
Wizard-Detected Dynamic IP Account Setup	35
Wizard-Detected IP Over ATM Account Setup	35
Wizard-Detected Fixed IP (Static) Account Setup	36
Testing Your Internet Connection	36
Manually Configuring Your Internet Connection	38
How to Perform Manual Configuration	38
Internet Connection Requires Login and Uses PPPoE	39
Internet Connection Requires Login and Uses PPPoA	40
Internet Connection Does Note Require A Login	41
ADSL Settings	42
Chapter 4 Wireless Configuration	43
Considerations for a Wireless Network	43
Observe Performance, Placement, and Range Guidelines	43
Implement Appropriate Wireless Security	44
Understanding Wireless Settings	46
How to Set Up and Test Basic Wireless Connectivity	49
How to Restricting Wireless Access to Your Network	50
Restricting Access to Your Network by Turning Off Wireless Connectivity	51
Restricting Wireless Access Based on the Wireless Network Name (SSID)	51
Restricting Wireless Access Based on the Wireless Station Access List	51
Choosing WEP Authentication and Security Encryption Methods	53
Authentication Type Selection	54
Encryption Choices	54
How to Configure WEP	55
How to Configure WPA-PSK	56
How to Configure WPA-802.1x	57
Chapter 5 Protecting Your Network	59
Protecting Access to Your 54 Mbps Wireless ADSL Modem Router Model DG834G	59
How to Change the Built-In Password	59
Changing the Administrator Login Timeout	60
Configuring Basic Firewall Services	60
Blocking Keywords, Sites, and Services	61
How to Block Keywords and Sites	61
Firewall Rules	63
Inbound Rules (Port Forwarding)	64
Inbound Rule Example: A Local Public Web Server	65
Outbound Rules (Service Blocking)	68
Order of Precedence for Rules	70
Services	70
How to Define Services	71
Setting Times and Scheduling Firewall Services	72
How to Set Your Time Zone	72
How to Schedule Firewall Services	73
Trend Micro Home Network Security	73
Security Service Settings	74
Parental Controls Settings	76
To enable Parental Controls:	76
To select Parental Controls Mode:	76
To configure General mode:	77
To configure Per-User mode:	77
Parental Controls Logs	78
Blocking criteria for potentially offensive categories	78
Chapter 6 Managing Your Network	81
Backing Up, Restoring, or Erasing Your Settings	81
How to Back Up the Configuration to a File	81
How to Restore the Configuration from a File	82
How to Erase the Configuration	82
Upgrading the ADSL Modem Router’s Firmware	82
How to Upgrade the ADSL Modem Router Firmware	83
Network Management Information	83
Viewing ADSL Modem Router Status and Usage Statistics	84
Viewing Attached Devices	89
Viewing, Selecting, and Saving Logged Information	89
Examples of Log Messages	92
Enabling Security Event E-mail Notification	93
Running Diagnostic Utilities and Rebooting the ADSL Modem Router	94
Enabling Remote Management	95
Configuring Remote Management	95
Chapter 7 Advanced Configuration	97
Configuring Advanced Security	97
Setting Up A Default DMZ Server	98
How to Configure a Default DMZ Server	98
Connect Automatically, as Required	99
Disable Port Scan and DOS Protection	99
Respond to Ping on Internet WAN Port	100
MTU Size	100
Configuring LAN IP Settings	100
DHCP	102
Use Router as DHCP server	103
Reserved IP addresses	103
How to Configure LAN TCP/IP Settings	104
Configuring Dynamic DNS	105
How to Configure Dynamic DNS	105
Using Static Routes	107
Static Route Example	107
How to Configure Static Routes	108
Universal Plug and Play (UPnP)	109
Chapter 8 Virtual Private Networking	111
Overview of VPN Configuration	112
Client-to-Gateway VPN Tunnels	112
Gateway-to-Gateway VPN Tunnels	113
Planning a VPN	113
VPN Tunnel Configuration	115
How to Set Up a Client-to-Gateway VPN Configuration	116
Step 1: Configuring the Client-to-Gateway VPN Tunnel on the DG834G	117
Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC	122
How to Set Up a Gateway-to-Gateway VPN Configuration	130
VPN Tunnel Control	137
Activating a VPN Tunnel	137
Verifying the Status of a VPN Tunnel	140
Deactivating a VPN Tunnel	142
Deleting a VPN Tunnel	145
How to Set Up VPN Tunnels in Special Circumstances	145
Using Auto Policy to Configure VPN Tunnels	146
Using Manual Policy to Configure VPN Tunnels	158
Chapter 9 Troubleshooting	161
Basic Functioning	161
Power LED Not On	162
Test LED Never Turns On or Test LED Stays On	162
LAN or WAN Port LEDs Not On	162
Troubleshooting the Web Configuration Interface	163
Troubleshooting the ISP Connection	164
ADSL link	164
WAN LED Blinking Yellow	164
WAN LED Off	164
Obtaining a WAN IP Address	165
Troubleshooting PPPoE or PPPoA	166
Troubleshooting Internet Browsing	166
Troubleshooting a TCP/IP Network Using the Ping Utility	167
Testing the LAN Path to Your Router	167
Testing the Path from Your Computer to a Remote Device	168
Restoring the Default Configuration and Password	169
Using the Reset button	169
Problems with Date and Time	169
Appendix A Technical Specifications	171
Appendix B Related Documents	173
Appendix C NETGEAR VPN Configuration	175
DG834G to FVL328	175
Configuration Profile	175
Step-By-Step Configuration	176
DG834G with FQDN to FVL328	181
Configuration Profile	181
The Use of a Fully Qualified Domain Name (FQDN)	182
Step-By-Step Configuration	183
Configuration Summary (Telecommuter Example)	188
Setting Up the Client-to-Gateway VPN Configuration (Telecommuter Example)	189
Step 1: Configuring the Client-to-Gateway VPN Tunnel on the VPN Router at the Employer’s Main Office	190
Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter’s Home Office	192
Monitoring the VPN Tunnel (Telecommuter Example)	200
Viewing the PC Client’s Connection Monitor and Log Viewer	200

Match case Limit results 1 per page

DG834G Reference Manual

Connecting the Router to the Internet

3-17

v3.0, September 2005

Note

: Disabling NAT will reboot the router and reset all the DG834G configuration settings to

the factory default. Disable NAT only if you plan to install the DG834G in a setting where you

will be manually administering the IP address space on the LAN side of the router.

Internet Connection Does Note Require A Login

If your Internet connection does

not

require a login, select No and fill in the settings according

to the instructions below.

Enter your Account Name (may also be called Host Name) and Domain Name.

These parameters may be necessary to access your ISP’s mail or news servers.

Internet IP Address:

•

Select “Get Dynamically from ISP” if your ISP uses DHCP to assign your IP address.

Your ISP will automatically assign these addresses.

•

Select “Use Static IP Address” if your ISP has assigned you a permanent, fixed (static) IP

address. Enter the IP address that your ISP assigned. Also enter the IP Subnet Mask and

the Gateway IP Address. The gateway is the ISP’s ADSL modem router to which your

ADSL modem router will connect.

•

Select “IP Over ATM (IPoA)” if your ISP uses Classical IP Addresses (RFC1577). Enter

the IP address, IP Subnet Mask, and Gateway IP Addresses that your ISP assigned.

Domain Name Server (DNS) Address:

•

Select “Get Dynamically from ISP” if your ISP uses DHCP to assign your IP address.

Your ISP will automatically assign this address.

•

If you know that your ISP does not automatically transmit DNS addresses to the ADSL

modem router during login, select “Use these DNS servers” and enter the IP address of

your ISP’s Primary DNS Server. If a Secondary DNS Server address is available, enter it

also.

A DNS server is a host on the Internet that translates Internet names (such as

www.netgear.com) to numeric IP addresses. Typically your ISP transfers the IP address of one

or two DNS servers to your ADSL modem router during login. If the ISP does not transfer an

address, you must obtain it from the ISP and enter it manually here.

You should only disable NAT if you are sure you do not require it. NAT automatically assigns

private IP addresses (192.168.0.x) to LAN connected devices. When NAT is disabled, only

standard routing is performed by this router.

Classical routing lets you directly manage the IP addresses the DG834G uses. Classical

routing should be selected only by experienced users.