Netgear RT311 RT314 Reference Manual - Page 103

LNK/ACT LEDs Not On, Wrong network configuration - drivers

Get Netgear RT311 PDF manuals and user guides
UPC - 606449004175
View all Netgear RT311 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

Reference Guide for the Model RT311 and RT314 Internet Access Gateway Routers If the path is not functioning correctly, you could have one of the following problems: • Wrong physical connections - Make sure the Local LNK/ACT LED is on. If the LNK/ACT LED is off, follow the instructions in "LNK/ACT LEDs Not On" on page 9-2. - Check that the corresponding Link LEDs are on for your network interface card and for the hub ports (if any) that are connected to your workstation and router. • Wrong network configuration - Verify that the Ethernet card driver software and TCP/IP software are both installed and configured on your PC or workstation. - Verify that the IP address for your router and your workstation are correct and that the addresses are on the same subnet. Troubleshooting 9-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
Reference Guide for the Model RT311 and RT314 Internet Access Gateway Routers
Troubleshooting
9-5
If the path is not functioning correctly, you could have one of the following problems:
•
Wrong physical connections
—
Make sure the Local LNK/ACT LED is on. If the LNK/ACT LED is off, follow the
instructions in
“LNK/ACT LEDs Not On
” on
page 9-2
.
—
Check that the corresponding Link LEDs are on for your network interface card and
for the hub ports (if any) that are connected to your workstation and router.
•
Wrong network configuration
—
Verify that the Ethernet card driver software and TCP/IP software are both installed
and configured on your PC or workstation.
—
Verify that the IP address for your router and your workstation are correct and that the
addresses are on the same subnet.