Netgear WFS709TP WFS709TP Setup Manual - Page 48

Connect the WFS709TP to the Network, Con the Default Gateway - manual pdf

Get Netgear WFS709TP - ProSafe Smart Wireless Controller PDF manuals and user guides
UPC - 606449052336
View all Netgear WFS709TP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

WFS709TP ProSafe Smart Wireless Switch Software Administration Manual Figure 2-9 5. Click Apply. Configure the Default Gateway The following configuration assigns a default gateway for the WFS709TP. 1. Navigate to the Configuration > Advanced > Switch > General > IP Routing page. 2. In the Default Gateway field, enter 10.3.22.1. 3. Click Apply. Connect the WFS709TP to the Network Connect the ports on the WFS709TP to the appropriately configured ports on an L2 switch or router. Make sure that you have the correct cables and that the port LEDs indicate proper connections. Refer to the document WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide for port LED and cable descriptions. Note: You can find the WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide in PDF form on the WFS709TP Resource CD. It is also available from the NETGEAR support site at http://www.netgear.com/support. To verify that the WFS709TP is accessible on the network: 2-12 Deploying a Basic WFS709TP System v1.0, June 2007

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
WFS709TP ProSafe Smart Wireless Switch Software Administration Manual
2-12
Deploying a Basic WFS709TP System
v1.0, June 2007
5.
Click Apply.
Configure the Default Gateway
The following configuration assigns a default gateway for the WFS709TP.
1.
Navigate to the Configuration > Advanced > Switch > General > IP Routing page.
2.
In the Default Gateway field, enter 10.3.22.1.
3.
Click Apply.
Connect the WFS709TP to the Network
Connect the ports on the WFS709TP to the appropriately configured ports on an L2 switch or
router. Make sure that you have the correct cables and that the port LEDs indicate proper
connections. Refer to the document
WFS709TP ProSafe Smart Wireless Switch Hardware
Installation Guide
for port LED and cable descriptions.
To verify that the WFS709TP is accessible on the network:
Figure 2-9
Note:
You can find the
WFS709TP ProSafe Smart Wireless Switch Hardware Installation
Guide
in PDF form on the WFS709TP
Resource CD
. It is also available from the
NETGEAR support site at
.