Netgear WPN824N WPN824N Setup Manual - Page 22

Basic Functions Are Not Working, Use this Computer's MAC Address, Apply - password reset

Get Netgear WPN824N - RangeMax Wireless-N 150 Router PDF manuals and user guides View all Netgear WPN824N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

RangeMax Wireless-N 150 Router Setup Manual Make sure that the Ethernet cables are securely plugged in: 1. Verify that the Internet status light on the wireless router will be lit if the Ethernet cable to the wireless router from the modem is plugged in securely and the modem and wireless router are both turned on (see "Router Front Panel" on page 3). 2. Verify that for each powered-on computer connected to the wireless router with a securely plugged in Ethernet cable, the corresponding wireless router LAN port status light is lit (see "Router Front Panel" on page 3). The label on the bottom of the wireless router identifies the number of each LAN port (see "Bottom Label" on page 5). Make sure that the network settings of the computer are correct: 1. Verify that your LAN connected computers are configured to obtain an IP address automatically through DHCP. For help with this, see the documentation for your computer or "Related Documents" on page 30. 2. Verify whether the MAC address is needed. Some cable modem services require you to use the MAC address of the computer registered on the account. If so, in the Router MAC Address section of the Basic Settings menu, select Use this Computer's MAC Address. To save your settings, click Apply. Restart the network in the correct sequence. Check the router status lights to verify correct router operation: If the Power light does not turn solid green within 2 minutes after you turn the router on, reset the router according to the instructions in "How Do I Restore the Default Password and Configuration Settings?" on page 24. Basic Functions Are Not Working After you turn on power to the router, check these status lights: 1. When power is first applied, verify that the Power light is on. a. Make sure that the power cord is properly connected to your router and that the power supply adapter is properly connected to a functioning power outlet. b. Check that you are using the power adapter supplied by NETGEAR for this product. If the error persists, you have a hardware problem and should contact technical support. 2. Verify that the Test light lights within a few seconds, indicating that the self-test procedure is running. Help with Troubleshooting 19 v1.0, November 2009

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
RangeMax Wireless-N 150 Router Setup Manual
Help with Troubleshooting
19
v1.0, November 2009
Make sure that the Ethernet cables are securely plugged in:
1.
Verify that the Internet status light on the wireless router will be lit if the Ethernet cable to the
wireless router from the modem is plugged in securely and the modem and wireless router are
both turned on (see
“Router Front Panel” on page 3
).
2.
Verify that for each powered-on computer connected to the wireless router with a securely
plugged in Ethernet cable, the corresponding wireless router LAN port status light is lit (see
“Router Front Panel” on page 3
). The label on the bottom of the wireless router identifies the
number of each LAN port (see
“Bottom Label” on page 5
).
Make sure that the network settings of the computer are correct:
1.
Verify that your LAN connected computers are configured to obtain an IP address
automatically through DHCP. For help with this, see the documentation for your computer or
“Related Documents” on page 30
.
2.
Verify whether the MAC address is needed. Some cable modem services require you to use
the MAC address of the computer registered on the account. If so, in the Router MAC Address
section of the Basic Settings menu, select
Use this Computer’s MAC Address
. To save your
settings, click
Apply
. Restart the network in the correct sequence.
Check the router status lights to verify correct router operation:
If the Power light does not turn solid green within 2 minutes after you turn the router on, reset the
router according to the instructions in
“How Do I Restore the Default Password and Configuration
Settings?” on page 24
.
Basic Functions Are Not Working
After you turn on power to the router, check these status lights:
1.
When power is first applied, verify that the Power light is on.
a.
Make sure that the power cord is properly connected to your router and that the power
supply adapter is properly connected to a functioning power outlet.
b.
Check that you are using the power adapter supplied by NETGEAR for this product.
If the error persists, you have a hardware problem and should contact technical support.
2.
Verify that the Test light lights within a few seconds, indicating that the self-test procedure is
running.