Oki B6500dn Guide: Network User's, B6500 (English Network User's Guide) - Page 25

Setting up the Workstation, Before Setup, Examples of Settings for Solaris 2.x

Get Oki B6500dn PDF manuals and user guides View all Oki B6500dn manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Setting up the Workstation This section explains the settings of Solaris 2.x workstation for printing. Before Setup Before setting up the workstation, check the following: > The setup procedures and commands may vary according to different versions of OS. Refer to the manuals that came with the workstation for details. > To setup the printer, the user must be a superuser. Contact your network administrator to perform the setup if you do not have the authority of a superuser. > Check the IP address set up for the printer in advance. Be cautious as an incorrect IP address may cause severe errors. > Before performing any network setup (such as the IP address) to a host running under NIS (Network Information Service), consult the NIS administrator. Examples of Settings for Solaris 2.x The examples below show printer settings for Solaris 2.6 where the printer host name is printer1. 1. Registering a printer (printer name: P001) supporting the PostScript language #lpadmin -p P001 -s printer1\!PS 2. Registering a printer (printer name: P002) supporting the PostScript language that feeds paper from an A4-size paper tray for duplex printing #lpadmin -p P002 -s printer1\!PS A4_DUP 3. Registering a logical PostScript printer PS01 set using the printer web page. #lpadmin -p P003 -s printer1\!PS01 NOTE > Enter the host name and printer name of the remote host after s by linking with !. The printer name corresponds to the print language/mode. > The output style may be specified at the same time. The parameters for specifying a style are the same as those available B6500 Network User's Guide Printing from UNIX - 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
B6500 Network User’s Guide
Printing from UNIX - 25
Setting up the Workstation
This section explains the settings of Solaris 2.x workstation for printing.
Before Setup
Before setting up the workstation, check the following:
>
The setup procedures and commands may vary according to
different versions of OS. Refer to the manuals that came with
the workstation for details.
>
To setup the printer, the user must be a superuser. Contact
your network administrator to perform the setup if you do not
have the authority of a superuser.
>
Check the IP address set up for the printer in advance. Be
cautious as an incorrect IP address may cause severe errors.
>
Before performing any network setup (such as the IP address)
to a host running under NIS (Network Information Service),
consult the NIS administrator.
Examples of Settings for Solaris 2.x
The examples below show printer settings for Solaris 2.6 where the printer
host name is printer1.
1.
Registering a printer (printer name: P001) supporting the
PostScript language
#lpadmin -p P001 -s printer1\!PS
2.
Registering a printer (printer name: P002) supporting the
PostScript language that feeds paper from an A4-size paper tray
for duplex printing
#lpadmin -p P002 -s printer1\!PS A4_DUP
3.
Registering a logical PostScript printer PS01 set using the printer
web page.
#lpadmin -p P003 -s printer1\!PS01
NOTE
>
Enter the host name and printer name of the remote host after -
s by linking with !. The printer name corresponds to the print
language/mode.
>
The output style may be specified at the same time. The
parameters for specifying a style are the same as those available