Oki LP470s LP470, LP480 User's Guide (English) - Page 51

Battery Strength, Signal Strength, Test Print Indicator, Two-line Text Display, Status messages

Get Oki LP470s PDF manuals and user guides View all Oki LP470s manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Battery Strength Three-segment indicator. • When all segments are lit, voltage level is greater than 8.0 V. • Two segments indicator a level of between 7.8 V and 7.9 V. • One segment indicates a level of between 7.6 V and 7.7 V. • When all segments are off (voltage level below 7.5 V) printing is not possible. Signal Strength Three-segment indicator: Minimum, Medium and Maximum signal quality. An X indicates no reception. Test Print Indicator Appears in Test Print mode. Two-line Text Display Displays the following: • Status messages: Firmware version, Online mode, Offline mode, labels remaining in print queue, Test Print status, Default Setting, Complete, Factory Clear, Press Feed Key, Press Print Key, Hex Dump Mode, Set up Display, Adjust LCD, Exit, Contrast, Back Light On • Warning messages: Cover Open, Paper End, Sensor Error, Buffer Near Full, Head Protect, Head Error, Module Error, • WLAN information: Messages such as Adhoc mode, Infrastructure mode, IP address, subnet mask, default gateway, Socket Port Number.Choosing the Label Dispensing mode You can choose to dispense labels in Continuous Mode or Dispense Mode. In either mode, test printing and online printing are available. 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
51
Battery Strength
Three-segment indicator.
²
When all segments are lit, voltage level is greater than 8.0 V.
²
Two segments indicator a level of between 7.8 V and 7.9 V.
²
One segment indicates a level of between 7.6 V and 7.7 V.
²
When all segments are off (voltage level below 7.5 V) printing
is not possible.
Signal Strength
Three-segment indicator: Minimum, Medium and Maximum
signal quality. An X indicates no reception.
Test Print Indicator
Appears in Test Print mode.
Two-line Text Display
Displays the following:
²
Status messages
: Firmware version, Online mode, Offline
mode, labels remaining in print queue, Test Print status,
Default Setting, Complete, Factory Clear, Press Feed Key,
Press Print Key, Hex Dump Mode, Set up Display, Adjust LCD,
Exit, Contrast, Back Light On
²
Warning messages
: Cover Open, Paper End, Sensor Error,
Buffer Near Full, Head Protect, Head Error, Module Error,
²
WLAN information:
Messages such as Adhoc mode,
Infrastructure mode, IP address, subnet mask, default
gateway, Socket Port Number.Choosing the Label Dispensing
mode
You can choose to dispense labels in
Continuous
Mode
or
Dispense Mode
. In either mode, test printing and online
printing are available.