Oki MICROLINE 1120 Users Guide 1 - Page 64

Djusting, Position

Get Oki MICROLINE 1120 PDF manuals and user guides View all Oki MICROLINE 1120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

MENU Serial I/F Item Baud Rate DTR Signal Busy Time Function Set the transmission speed of the serial interface. Set whether to switch the DTR signal of the serial interface by Select/ Deselect or hold it after power-on. Set the minimum time it takes to switch from a busy state to a ready state. Setting 9,600 bps 4,800 bps 2,400 bps 1,200 bps 600 bps 300 bps 19,200 bps Ready on Power UP Ready on Select 0.2 sec 1.0 sec Initialising menu settings To restore the menu settings to their initial values, carry out the steps below. NOTE The values adjusted by the Adjustment menus are not initialised by the following procedure. 1. Set the Power Switch to OFF. 2. Press and hold down the SEL and LF/FF buttons together and then set the Power Switch to ON. Adjusting TOF position Use the following procedure to set TOF to accord with the reference position (23.28 mm (11/12 in)). The reference position refers to the first line of the paper i.e. the position to which the printer feeds the paper when automatically loading the paper. NOTE Adjusting of TOF can be done in cut sheet mode or continuous forms mode. ML1120/ML1190 User's Guide - Operating instructions > 64

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
ML1120/ML1190 User’s Guide - Operating instructions > 64
I
NITIALISING
MENU
SETTINGS
To restore the menu settings to their initial values, carry out the steps
below.
NOTE
The values adjusted by the Adjustment menus are not initialised by
the following procedure.
1.
Set the Power Switch to OFF.
2.
Press and hold down the SEL and LF/FF buttons together and
then set the Power Switch to ON.
A
DJUSTING
TOF
POSITION
Use the following procedure to set TOF to accord with the reference
position (23.28 mm (11/12 in)). The reference position refers to the first
line of the paper i.e. the position to which the printer feeds the paper
when automatically loading the paper.
NOTE
Adjusting of TOF can be done in cut sheet mode or continuous
forms mode.
MENU
ITEM
FUNCTION
SETTING
Serial I/F
Baud Rate
Set the transmission
speed of the serial
interface.
9,600 bps
4,800 bps
2,400 bps
1,200 bps
600 bps
300 bps
19,200 bps
DTR Signal
Set whether to switch
the DTR signal of the
serial interface by Select/
Deselect or hold it after
power-on.
Ready on Power UP
Ready on Select
Busy Time
Set the minimum time
it takes to switch from
a busy state to a ready
state.
0.2 sec
1.0 sec