Onkyo CR-N765 User Manual English - Page 12

Getting started

Get Onkyo CR-N765 PDF manuals and user guides View all Onkyo CR-N765 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Getting started 1. Connecting speakers Refer to the illustration below to connect the unit and the right and left speakers with the speaker cables. Connect the speaker to be placed on the right hand side to the SPEAKERS terminal (R), and connect the speaker to be placed on the left hand side to the SPEAKERS terminal (L). Since the unit is equipped with the SUBWOOFER PRE OUT terminal, you can enhance bass sound playback by connecting a subwoofer with a built-in power amplifier. Important: Connect speakers with 4 h to 16 h impedance. Connecting a speaker with a lower impedance may damage the speaker. Left speaker Right speaker Speaker cable failure. Also do not connect two or more cables to one speaker terminal or one speaker to several terminals. 2. AM/FM antenna connections Connect the antennas to listen to AM/FM broadcast. When listening to the broadcast for the first time, adjust the antenna position and orientation to get the best reception. Insert the plug fully into the jack. Fix with a tack on the wall. Indoor FM antenna (supplied) AM loop antenna (supplied) Powered subwoofer 12-15 mm Cut and remove the plastic coating from the end of the speaker cable, twist the core and connect it to the terminal. Make correct connection between the unit's jacks and speaker's jacks (i to i and j to j) for each channel. If connection is wrong, a bass sound may become poor due to reverse phase. 0 Short-circuiting the i cable and j cable or contacting the cable core to the rear panel of the unit may cause Assemble the AM loop antenna (supplied). 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
12
Getting started
1. Connecting speakers
Refer to the illustration below to connect the unit and the
right and left speakers with the speaker cables. Connect
the speaker to be placed on the right hand side to the
SPEAKERS terminal (R), and connect the speaker to be
placed on the left hand side to the SPEAKERS terminal
(L). Since the unit is equipped with the SUBWOOFER
PRE OUT terminal, you can enhance bass sound
playback by connecting a subwoofer with a built-in power
amplifier.
Important:
Connect speakers with 4
h
to 16
h
impedance. Connecting a speaker with a lower
impedance may damage the speaker.
Cut and remove the plastic coating from the end of the
speaker cable, twist the core and connect it to the
terminal. Make correct connection between the unit’s
jacks and speaker’s jacks (
i
to
i
and
j
to
j
) for each
channel. If connection is wrong, a bass sound may
become poor due to reverse phase.
0
Short-circuiting the
i
cable and
j
cable or contacting
the cable core to the rear panel of the unit may cause
failure. Also do not connect two or more cables to one
speaker terminal or one speaker to several terminals.
2. AM/FM antenna connections
Connect the antennas to listen to AM/FM broadcast.
When listening to the broadcast for the first time, adjust
the antenna position and orientation to get the best
reception.
Left speaker
Right speaker
Powered subwoofer
Speaker cable
12-15 mm
Insert the plug fully into the
jack.
Indoor FM
antenna
(supplied)
Fix with a tack on
the wall.
AM loop antenna (supplied)
Assemble the AM loop antenna (supplied).