Onkyo HT-R570 Owner Manual

Onkyo HT-R570 Manual

Get Onkyo HT-R570 PDF manuals and user guides View all Onkyo HT-R570 manuals
Add to My Manuals
Save this manual to your list of manuals

Onkyo HT-R570 manual content summary:

  • Onkyo HT-R570 | Owner Manual - Page 1
    1ch Home Theater System HT-S5200 AV Receiver (HT-R570) Speaker Package (HTP-570) Front Speakers (SKF-570 L/R) Center Speaker (SKC-570) Surround Speakers (SKR-570 L/R) Surround Back Speakers (SKB-570 L/R) Subwoofer (SKW-570) Dock for iPod (UP-A1L) Instruction Manual Thank you for purchasing an Onkyo
  • Onkyo HT-R570 | Owner Manual - Page 2
    (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING AVIS instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work
  • Onkyo HT-R570 | Owner Manual - Page 3
    not work properly the next time you turn it on, so be sure to use it occasionally. For U.S. models FCC Information for User CAUTION: The user changes from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV techni- cian for help. For Canadian Models NOTE: THIS
  • Onkyo HT-R570 | Owner Manual - Page 4
    howling or slipping of sound may occur. To audio cables (Always turn off your amplifier before connecting or disconnecting cables.) 7. Microphone feedback. 4 Make sure you have the following accessories: AV receiver HT-R570 HT-R570 Remote controller and two batteries (AA/R6) Speaker setup microphone
  • Onkyo HT-R570 | Owner Manual - Page 5
    Package Contents-Continued Speaker Package HTP-570 Front speakers (SKF-570 L/R) 4 rubber spacers for center speaker Dock for iPod UP-A1L Center speaker (SKC-570) Surround speakers (SKR-570 L/R) Surround back speakers (SKB-570 L/R) * In catalogs and on packaging, the letter at the end of the
  • Onkyo HT-R570 | Owner Manual - Page 6
    of Speakers Speaker Sets A and B You can use two sets of speakers with the AV receiver: speaker set A and speaker set B. Speaker set A should be used in your main listening room for up to 7.1-channel playback. * While speaker set B is on, speaker set A is reduced to 5.1-channel playback. Speaker set
  • Onkyo HT-R570 | Owner Manual - Page 7
    AV Receiver HT-R570 coded speaker terminals and speaker cable SKW-570 Bass Reflex Powered Subwoofer • 25 cm (10") cone woofer • Max. power:290 W Dock for iPod UP-A1L • Easily links iPod Touch (1G, 2G), iPod Classic, iPod (4G, 5G), iPod nano (1G, 2G, 3G, 4G), iPod mini with Onkyo A/V Systems
  • Onkyo HT-R570 | Owner Manual - Page 8
    marks and logos are the property of their respective owners. All rights reserved. SIRIUS subscription sold separately. Taxes and a onetime activation fee may apply. SIRIUS tuner required (sold separately) to receive the SIRIUS service. All programming and fees subject to change. It is prohibited to
  • Onkyo HT-R570 | Owner Manual - Page 9
    Important Safety Instructions 2 Precautions 3 Speaker Precautions 4 Package Contents 4 AV receiver HT-R570 4 Speaker Package HTP-570 5 Dock for iPod UP-A1L 5 Using Two Sets of Speakers 6 Speaker Sets A and B 6 Features 7 AV Receiver HT-R570 7 Speaker Package HTP-570 7 Dock for iPod
  • Onkyo HT-R570 | Owner Manual - Page 10
    for each item. B ON/STANDBY button (38) Sets the AV receiver to On or Standby. C STANDBY indicator (38) Lights up when the AV receiver is on Standby and flashes while a signal is being received from the remote controller. D SPEAKERS A & B buttons (18, 44) Turn speaker sets A and B on or off
  • Onkyo HT-R570 | Owner Manual - Page 11
    and Speaker Setup microphone connects here. E F GH For detailed information, see the pages in parentheses. B A and B speaker indicators (18, 44) Indicator A lights up when speaker set A is on. Indicator B lights up when speaker set B is on. C MUTING indicator (45) Flashes while the AV receiver is
  • Onkyo HT-R570 | Owner Manual - Page 12
    surround, and surround back speakers. K V REMOTE CONTROL This V (Remote Interactive) jack can be connected to the V jack on another V-capable Onkyo component for remote and system control. To use V, you must make an analog audio connection (RCA) between the AV receiver and the other component, even
  • Onkyo HT-R570 | Owner Manual - Page 13
    is composite video input jacks for connecting the video signal, and there are analog audio input jacks for connecting the audio signal. R SUBWOOFER PRE OUT This analog audio output can be connected to a powered subwoofer. S FRONT SPEAKERS B These push terminals are for connecting speaker set B. 13
  • Onkyo HT-R570 | Owner Manual - Page 14
    no input signal for a while, the SKW-570 automatically enters Standby mode. C OUTPUT LEVEL control (44) This control is used to adjust the volume of the subwoofer. D LINE INPUT (20) This RCA input should be connected to the subwoofer pre out on the AV receiver with supplied RCA cable. Note: The Auto
  • Onkyo HT-R570 | Owner Manual - Page 15
    SKC-570 B C B Keyhole slots These keyhole slots can be used to wall-mount the speaker. See page 21 for mounting instructions. C Speaker terminals These push terminals are for connecting the speaker to the HT-R570 with the supplied speaker cables. The supplied speaker cables are color-coded for
  • Onkyo HT-R570 | Owner Manual - Page 16
    AV receiver to On or Standby. C REMOTE MODE/INPUT SELECTOR buttons (44, 61, 80-83) Selects the remote controller modes and the input sources. D SP A/B button (18, 44) This button is used to turn speaker sets A and B on or off. 16 E Arrow [R]/[X]/[F]/[S] and ENTER buttons Used to select and adjust
  • Onkyo HT-R570 | Owner Manual - Page 17
    , as shown below. Remote control sensor STANDBY indicator AV receiver 2 Insert the two supplied batteries (AA/R6) in accordance with the polarity diagram inside the battery compartment. 3 Replace the cover and push it shut. Notes: • If the remote controller doesn't work reliably, try replacing
  • Onkyo HT-R570 | Owner Manual - Page 18
    TV, you can enjoy Dolby Pro Logic IIx, DTS Neo:6, or Onkyo's original DSP listening modes. Front left and right speakers (SKF-570) These output the main sound. Their role in a home theater is to provide a solid anchor for the sound image. They should be positioned facing the listener at about ear
  • Onkyo HT-R570 | Owner Manual - Page 19
    To get the best from your surround-sound system, you must set the speaker settings. You can do this automatically (see page 39) or manually (see page 70). Speaker Connection Precautions Read the following before connecting your speakers: • You can connect speakers with an impedance of between 6 and
  • Onkyo HT-R570 | Owner Manual - Page 20
    Connecting the AV receiver-Continued Connecting Speaker Set A 1 Strip 1/2"-5/8" (12-15 1/2"-5/8"(12-15mm) mm) of insulation from the ends of the speaker cables. (Supplied speaker cables are already stripped.) 2 Unscrew the terminal. Fully insert the bare wire, making sure that it's touching
  • Onkyo HT-R570 | Owner Manual - Page 21
    the AV receiver-Continued Wall Mounting The speakers can easily be wall mounted by using the keyhole slots. To mount the front or surround speakers vertically, use the keyhole slot shown to hang each speaker on a screw that's securely screwed into the wall. Front speakers (SKF-570) Keyhole
  • Onkyo HT-R570 | Owner Manual - Page 22
    ready for use, you'll need to tune into an AM radio station and adjust the position of the AM antenna to achieve the best possible reception. Keep the antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords. If you cannot achieve good reception with the supplied
  • Onkyo HT-R570 | Owner Manual - Page 23
    and TV reception, as this can cause interference problems. If circumstances demand it, use a TV/FM antenna splitter, as shown. Outdoor AM antennas work best when installed horizontally outside, but good prevent electrical shock hazards. TV/FM antenna splitter To AV receiver To TV (or VCR) 23
  • Onkyo HT-R570 | Owner Manual - Page 24
    keep audio and video cables away from power cords and speaker cables. Right! Wrong! Video/Audio HDMI Cable Jack HDMI Description HDMI connections can carry uncompressed standardor high-definition digital video and audio and offer the best picture and sound quality. Video Component video cable
  • Onkyo HT-R570 | Owner Manual - Page 25
    simply by changing the input source on the AV receiver. : Signal Flow Video Video Audio Audio TV, projector, etc. DVD/BD player, etc. Speakers (see page 20 for hookup details) Which Connections Should I Use? The AV receiver supports several connection formats for compatibility with a wide
  • Onkyo HT-R570 | Owner Manual - Page 26
    Digital Content Protection),*2 a copy-protection system for digital video signals. Other devices connected to the AV receiver via HDMI must also support HDCP. Use a commercially available HDMI cable (supplied with some components) to connect the AV receiver's HDMI OUT to the HDMI input on your TV or
  • Onkyo HT-R570 | Owner Manual - Page 27
    signals from a PC are not supported. • When listening to an HDMI component through the AV receiver, set the HDMI component so that its video can be seen on the TV screen (on the TV, select the input of the HDMI component connected to the AV receiver). • The HDMI audio signal (sampling rate, bit
  • Onkyo HT-R570 | Owner Manual - Page 28
    VIDEO IN Connect one or the other Connection b must be assigned (see page 42) TV, projector, etc. Hint! If your TV has no audio outputs, connect an audio output from your VCR or cable or satellite receiver to the AV receiver and use its tuner to listen to TV programs through the AV receiver
  • Onkyo HT-R570 | Owner Manual - Page 29
    a DVD/BD player Step 1: Video Connection Choose a video connection that matches your DVD/BD player ( A or B ), and then make the connection. You must connect the AV receiver to your TV with the same type of connection. Step 2: Audio Connection Choose an audio connection that matches your DVD/BD
  • Onkyo HT-R570 | Owner Manual - Page 30
    hookup, you can use the tuner in your VCR or DVR to listen to your favorite TV programs via the AV receiver, which is useful if your TV has no audio outputs. Step 1: Video Connection Choose a video connection that matches your VCR or DVR ( A or B ), and then make the connection. You must connect
  • Onkyo HT-R570 | Owner Manual - Page 31
    OUT V VCR/DVR OUT L/R Signal flow ⇒ ⇒ VCR or DVD recorder Composite video input Audio L/R input C A a VIDEO IN L R AUDIO IN VCR or DVR Notes: • The AV receiver must be turned on for recording. Recording is not possible while it's on Standby. • If you want to record directly from your TV or
  • Onkyo HT-R570 | Owner Manual - Page 32
    the AV receiver-Continued Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source Hint! With this hookup, you can use your satellite or cable receiver to listen to your favorite TV programs via the AV receiver, which is useful if your TV has no audio outputs. Step 1: Video
  • Onkyo HT-R570 | Owner Manual - Page 33
    AUX INPUT VIDEO Connection A a AV receiver AUX INPUT VIDEO AUX INPUT L-AUDIO-R Signal flow ⇐ ⇐ Connecting a Portable Audio player Step 1: Make the audio connection a . L AUDIO R OUT Camcorder, game console, etc. VIDEO OUT Camcorder or console Composite video output Analog audio L/R output AUX
  • Onkyo HT-R570 | Owner Manual - Page 34
    the CD player. • To connect the CD player digitally, use connection b or c . IN L R CD a L R AUDIO OUTPUT Turntable (MM) with built-in phono preamp Connection a b c AV receiver Signal flow CD IN L/R ⇐ DIGITAL IN COAXIAL 1 (DVD/BD) ⇐ DIGITAL IN OPTICAL 2 (CD) ⇐ CD or turntable Analog
  • Onkyo HT-R570 | Owner Manual - Page 35
    page 42) OPTICAL OUT COAXIAL OUT L R AUDIO IN L R AUDIO OUT Cassette, CDR, MD, etc. • With connection a , you can play and record. • To connect the recorder digitally for playback, use connections a and b , or a and c . Connection a b c AV receiver TV/TAPE IN L/R TV/TAPE OUT L/R DIGITAL
  • Onkyo HT-R570 | Owner Manual - Page 36
    one or the other ■ If Your iPod Doesn't Support Video: Connect your RI Dock's audio output jacks to the AV receiver's TV/TAPE IN L/R jacks. IN L R TV/TAPE Notes: • Enter the appropriate remote control code before using the AV receiver's remote controller for the first time (see page 78). • Connect
  • Onkyo HT-R570 | Owner Manual - Page 37
    sure that each Onkyo component is connected to the AV receiver with an analog audio cable (RCA). Step 2: Make the necessary V connections (see illustration below). Step 3: If you're using an MD, CDR, or RI DOCK component, change the Input Display (see page 43). With V (Remote Interactive), you can
  • Onkyo HT-R570 | Owner Manual - Page 38
    Few Easy Steps To get your system up and running with the minimum of fuss, here's a few pointers to help you configure the AV receiver before you use it for the very first time. These settings only need to be made once. ■ Do the 2EQ Room Correction and Speaker Setup-this is essential! See "Audyssey
  • Onkyo HT-R570 | Owner Manual - Page 39
    This section explains the settings that you need to make before using the AV receiver for the very first time. Audyssey 2EQ™ Room Correction and Speaker Setup With the supplied calibrated microphone, Audyssey 2EQ automatically determines the number of speakers connected, their size for purposes
  • Onkyo HT-R570 | Owner Manual - Page 40
    audio electronics during the measurement process as Radio Frequency Interference (RFI) may cause measurement disruptions (even if the cell phone is not in use). 3 Press [ENTER]. The room calibration and speaker setup starts. 1 2 40 ENTER Turn on the AV receiver. Set the speaker setup microphone
  • Onkyo HT-R570 | Owner Manual - Page 41
    Settings Manually If you wish to make changes to the settings found during the room correction and speaker setup, follow the directions on pages 70-72. Using a Powered Subwoofer If you're using a powered subwoofer, as it outputs very low-frequency sound and its position is usually low down, it
  • Onkyo HT-R570 | Owner Manual - Page 42
    CD PORT Default assignment IN1 ----IN2 1 Press the [RECEIVER] button, followed by the [SETUP] button. Digital Input Setup To enjoy Dolby Digital and DTS, you must connect your DVD/BD player to the AV receiver by using a digital audio connection (coaxial or optical). Here are the default
  • Onkyo HT-R570 | Owner Manual - Page 43
    If you connect an V-capable Onkyo MiniDisc recorder, CD recorder, or RI Dock to the TV/TAPE IN/OUT jacks, or connect an RI Dock to the CBL/SAT IN or VCR/DVR IN jacks, for V to work properly, you must change this setting. This setting can only be changed on the AV receiver. VCR/DVR 1 or Press
  • Onkyo HT-R570 | Owner Manual - Page 44
    receiver's HDMI OUT, COMPONENT VIDEO OUT, or MONITOR OUT. On some DVD/BD players, you may need to change the digital or HDMI audio output settings. To adjust the volume, use the MASTER VOLUME control or the remote controller's VOL [R]/[X] button. Since the AV receiver is designed for home theaters
  • Onkyo HT-R570 | Owner Manual - Page 45
    You can also use the AV receiver's [DIMMER] button. AV receiver To unmute the AV receiver, press the remote controller's [MUTING] button again, or adjust the volume. The output is unmuted and the MUTING indicator goes off. Muting is cancelled when the AV receiver is set to Standby. Using the Sleep
  • Onkyo HT-R570 | Owner Manual - Page 46
    Adjusting the Bass & Treble You can adjust the bass or treble for speaker set A's front speakers, except when the Direct listening mode is selected. AV receiver the remote controller by using [AUDIO] button (see page 76). ■ Bass You can boost or cut low-frequency sounds output by the front speakers
  • Onkyo HT-R570 | Owner Manual - Page 47
    AV receiver's [MUSIC OPTIMIZER] button. The setting is stored individually for each input selector. Off: Music Optimizer off (default). On: Music Optimizer on. Tip: This procedure can also be performed on the remote controller by using [AUDIO and there will be no sound. DTS: Only DTS format input
  • Onkyo HT-R570 | Owner Manual - Page 48
    AM/FM Frequency Step Setup ENTER SETUP RECEIVER RXFS For AM/FM tuning to work properly, you must specify the AM/FM frequency step used in your area. Note that when this setting is changed, all radio presets are deleted. 1 Press the [RECEIVER] button, followed by the [SETUP] button. 4 Use the
  • Onkyo HT-R570 | Owner Manual - Page 49
    FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono. Note: You can also use the remote controller's Up and Down [R]/[X] buttons to tune the radio. 2 Press the TUNING Up or Down [R]/[X] button. Searching
  • Onkyo HT-R570 | Owner Manual - Page 50
    Listening to the Radio-Continued ■ Tuning into Stations by Frequency You can tune into AM and FM stations directly by entering the appropriate frequency. Displaying AM/FM Radio Information DISPLAY TUNER Press the [DISPLAY] button to display the available information. Number buttons D.TUN Band
  • Onkyo HT-R570 | Owner Manual - Page 51
    holding down the [MEMORY] button, press the [TUNING MODE] button. The preset is deleted and its number disappears from the display. Number buttons AV receiver To select a preset, use the PRESET [F]/[S] buttons or the remote controller's CH [+/-] button. or Remote controller You can also
  • Onkyo HT-R570 | Owner Manual - Page 52
    . Once you've purchased a SIRIUS tuner you'll need to activate it and subscribe to begin enjoying the service. Easy to follow installation and setup instructions are provided with the SIRIUS tuner. There are a variety of programming packages available, including the option of adding "The Best of XM
  • Onkyo HT-R570 | Owner Manual - Page 53
    your SIRIUS Satellite Radio ID, which you can get from the AV receiver, as explained below, or from the SiriusConnect Home tuner package. 1 Remote controller Press the [RECEIVER] button, followed by the [SETUP] button. 3 Remote controller Use the Up and Down [R]/[X] buttons to select "SATRadio
  • Onkyo HT-R570 | Owner Manual - Page 54
    , and then press the [ENTER] button repeatedly to select Channel Search mode. Remote controller This procedure can also be performed on the AV receiver by using its [TUNER] button, and [TUNING MODE] button. /// ENTER TUNER 2 AV receiver Use the Up and Down [R]/[X] buttons to select a channel
  • Onkyo HT-R570 | Owner Manual - Page 55
    on the AV receiver by using its [TUNER] button, and [TUNING MODE] button. MEMORY ENTER DISPLAY DISPLAY 2 AV receiver Use the Left and Right [F]/[S] buttons to select a category, and use the Up and Down [R]/[X] buttons to select a channel in that category. Remote controller SETUP D.TUN CH
  • Onkyo HT-R570 | Owner Manual - Page 56
    channels from the currently selected category. Selecting the Previous Channel: AV receiver Remote controller To listen to the previously selected SIRIUS Satellite Radio channel, press the [RETURN] button. 4 AV receiver Press the [MEMORY] button again to store the channel. The channel is stored
  • Onkyo HT-R570 | Owner Manual - Page 57
    delete. See the previous section. 2 AV receiver While holding down the [MEMORY] button, press the [TUNING MODE UPDATING XXX% Displayed while the channel map is being updated. Wait until the updating is complete. SIRIUS UPDATING Displayed while the SiriusConnect receiver's firmware is being updated
  • Onkyo HT-R570 | Owner Manual - Page 58
    1 Press the [RECEIVER] button, followed by the [SETUP] button. The message "Locked" will appear on the display. 6 Press the [SETUP] button. Setup closes. * The default number is "0000." If you want to change the default setting, see "Changing the PIN Number" on page 59. To unlock a previously
  • Onkyo HT-R570 | Owner Manual - Page 59
    the [RECEIVER] button, followed by the [SETUP] button. Enter the new PIN number again. If you enter the wrong PIN number, "Wrong Code!" [SETUP] button. Setup closes. 2 Use the Up and Down [R]/[X] buttons to select "10. Parental Lock", and then press [ENTER]. Note: If the "SATRadio" is set
  • Onkyo HT-R570 | Owner Manual - Page 60
    movie stored on your Apple iPod through the AV receiver and enjoy great sound. You can use the AV receiver's remote controller to operate your iPod. For the latest information on the Dock, see the Onkyo Web site at: www.onkyo.com iPod adapter ■ Adjusting the iPod Adapter The iPod adapter needs to
  • Onkyo HT-R570 | Owner Manual - Page 61
    will be charged when the AV receiver is set to "On" or "Standby". Note: When UP-A1L is connected, the power consumption on standby mode slightly increases. Controlling iPod To control your iPod when it's seated in the UP-A1L Dock, which is connected to the HT-R570's PORT jack, press the [PORT
  • Onkyo HT-R570 | Owner Manual - Page 62
    Dock for iPod-Continued G MUTING button (45) Mutes or unmutes the AV receiver. H ALBUM +/- button Selects the next or previous album. I VOL [R]/[X] button (44) Adjusts the volume of the AV receiver from your iPod. ❏ Dock does not support the control The iPod being used is not supported by this unit.
  • Onkyo HT-R570 | Owner Manual - Page 63
    to record audio and video from separate sources. Notes: • The surround sound and DSP listening AV Sources You can overdub audio onto your video recordings by simultaneously recording audio and video from two separate sources. This is possible because only the audio source is switched when an audio
  • Onkyo HT-R570 | Owner Manual - Page 64
    your DVD/BD player is connected to the AV receiver with a digital audio connection (OPTICAL, or COAXIAL). • The AV receiver Selecting with the Remote Controller MOVIE/TV MUSIC STEREO GAME Press the [RECEIVER the listening modes intended for use with video games. ■ LISTENING MODE buttons [MOVIE/
  • Onkyo HT-R570 | Owner Manual - Page 65
    can be selected. Front L Speaker Center Speaker Surround L Speaker Surround back L Speaker FL C FR Front R Speaker SW Subwoofer Surround R SL SR Speaker Surround back SBL SBR R Speaker C : active in the speaker settings C : non-active in the speaker settings Mono/Multiplex Sources
  • Onkyo HT-R570 | Owner Manual - Page 66
    SBL SBR ✔ ✔ ✔ ✔*1 ✔*1 ✔*1 SBL SBR ✔ ✔ ✔ ✔ ✔ AllChStereo ✔ ✔ ✔ FullMono ✔ ✔ ✔ T-D (Theaterdimensional) ✔ ✔ ✔ ✔ Notes: *1 If there are no surround back speakers, or speaker set B is on, Dolby Pro Logic II is used. • Available sampling rate for PCM input signal is 32
  • Onkyo HT-R570 | Owner Manual - Page 67
    Using the Listening Modes-Continued 5.1 channel Sources ✔: Available Listening Modes Speaker layout Listening Mode Button FL C FR FL C FR FL C FR FL C FR SW SW SW SW SL SR SL SR SL SR SL SR Direct
  • Onkyo HT-R570 | Owner Manual - Page 68
    Using the Listening Modes-Continued About the Listening Modes The AV receiver's listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. Direct In this mode, audio from the input source is output directly with minimal
  • Onkyo HT-R570 | Owner Manual - Page 69
    Using the Listening Modes-Continued Onkyo Original DSP Modes Orchestra Suitable for classical or the listening room. T-D (Theater-Dimensional) With this mode you can enjoy a virtual surround sound even with only two or three speakers. This works by controlling how sounds reach the listener's left and
  • Onkyo HT-R570 | Owner Manual - Page 70
    procedure can also be performed on the AV receiver by using its [SETUP] button, arrow buttons, and [ENTER] button. Speaker Settings This section explains how to check the speaker settings and how to set them manually, which is useful if you change a speaker after performing the Audyssey 2EQ™ Room
  • Onkyo HT-R570 | Owner Manual - Page 71
    up the frequency response in the manuals supplied with your speakers and set accordingly. • Choose a higher crossover frequency if you want more sound from your subwoofer. Double Bass This setting is not set automatically by the Audyssey 2EQ Room Correction and Speaker Setup function (see page 39
  • Onkyo HT-R570 | Owner Manual - Page 72
    cannot be changed while a pair of headphones is connected, or speaker set A is off, or speaker set B is on, or the AV receiver is muted. Left, Center, Right, SurrRight, SurrBack Right, SurrBack Left, SurrLeft, Subwoofer The levels can be adjusted from -12 to +12 dB in 1 dB steps (-15 to +12 dB
  • Onkyo HT-R570 | Owner Manual - Page 73
    Setup-Continued Audio Adjust Settings With the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like. 7. Audio Adjust Multiplex/Mono Settings not enough surround sound, move it backward. Center Width 0 to 7 (default: 3) from the center speaker when using
  • Onkyo HT-R570 | Owner Manual - Page 74
    Audyssey Dynamic Volume™ off. Light: Light Compression Mode becomes active (see page 39). Medium: Medium Compression Mode becomes active (see page 39). Heavy: Heavy Compression Mode becomes active. This setting affects volume the most, causing all sounds to be of equal loudness. Notes: • Other than
  • Onkyo HT-R570 | Owner Manual - Page 75
    Advanced Setup-Continued Hardware Setup This section explains items on the Hardware menu. 8. Hardware Remote ID When several Onkyo components are used in the same room, their remote ID codes may overlap. To differentiate the AV receiver from the other components, you can change its remote ID from 1,
  • Onkyo HT-R570 | Owner Manual - Page 76
    settings. AUDIO Tone Control Settings You can adjust the bass and treble for the front speakers, except when the Direct listening mode is selected. Notes: • To bypass the bass and treble tone circuits, select the Direct listening mode. • This procedure can also be performed on the AV receiver
  • Onkyo HT-R570 | Owner Manual - Page 77
    Music Optimizer on. Speaker Levels You can adjust the volume of each speaker while listening to an input source. These temporary adjustments are cancelled when the AV receiver is set to Standby. Notes: • You cannot use this function while the AV receiver is muted. • Speakers that are set to "No" or
  • Onkyo HT-R570 | Owner Manual - Page 78
    (page 82) Onkyo Dock (pages 61, 83) Entering Remote Control Codes You'll need to enter a code for each component that you want to control. Remote indicator REMOTE MODE DISPLAY RECEIVER AUDIO Number buttons 1 Look up the appropriate remote control code in the separate Remote Control Codes list
  • Onkyo HT-R570 | Owner Manual - Page 79
    a remote control code. When a button is reset, its preprogrammed code is restored. Resetting the Remote Controller You can reset the remote controller to its default settings. 1 While holding down the [RECEIVER] button, press and hold down the [AUDIO] button until the Remote indicator lights
  • Onkyo HT-R570 | Owner Manual - Page 80
    remote control code for controlling an Onkyo DVD player. For details on entering a remote control code for a different component, see page 78. Press the appropriate REMOTE MODE button first B J K L M C N D E O P F G Q H R I S B ON/STANDBY button Sets the DVD player to On or Standby
  • Onkyo HT-R570 | Owner Manual - Page 81
    is preprogrammed with the remote control code for controlling an Onkyo CD player. For details on entering a remote control code for a different component, see page 78. Press the appropriate REMOTE MODE button first B I J K L C D E F M G N H O B ON/STANDBY button Set the component to On
  • Onkyo HT-R570 | Owner Manual - Page 82
    button (45) Mutes or unmutes the AV receiver. H VOL [R]/[X] button (44) Adjusts the volume of the AV receiver. I Stop [] button Stops playback. Notes: • With some components, certain buttons may not work as expected, and some may not work at all. • An Onkyo cassette recorder connected via V can
  • Onkyo HT-R570 | Owner Manual - Page 83
    a remote control code, see page 78. When Using an RI Dock: • Connect the RI Dock to the TV/TAPE IN, VCR/DVR IN, or CBL/SAT IN L/R jacks. • Set the RI Dock's RI MODE switch to "HDD" or "HDD/DOCK". • Set the AV receiver's Input Display to "DOCK" (see page 43). • See to the Dock's instruction manual
  • Onkyo HT-R570 | Owner Manual - Page 84
    If the AV receiver turns off when you set the volume to maximum, disconnect the power cord, and contact your Onkyo dealer. Audio There's no sound or it's very quiet • Press the SPEAKERS [A] or [B] button to turn on the indicator for the speakers that you want to output sound. • HDMI audio is passed
  • Onkyo HT-R570 | Owner Manual - Page 85
    Troubleshooting-Continued The subwoofer produces no sound • The subwoofer outputs no sound while only speaker set B is on. Turn on speaker set A. • If the source material contains no audio in the LFE channel, the subwoofer produces no sound. • Check the "3. Sp Config" (page 70). • On the AV receiver
  • Onkyo HT-R570 | Owner Manual - Page 86
    , certain buttons may not work as expected, and some may not work at all. • To control an Onkyo component that's connected via V, point the remote controller at the AV receiver. Be sure to enter the appropriate remote control code first (page 79). Dock for iPod There's no sound • Make sure your iPod
  • Onkyo HT-R570 | Owner Manual - Page 87
    Troubleshooting-Continued The following settings can be made for the composite video inputs You must use the buttons on the unit to make these settings. 1. While holding down the input selector button for the input source that you want to set, press the [SETUP Onkyo set the AV receiver to Standby. 87
  • Onkyo HT-R570 | Owner Manual - Page 88
    Specifications HT-R570 Amplifier Video Outputs HDMI Component Composite OUT OUT VCR/DVR (REC OUT), MONITOR OUT ■ Audio Inputs Digital Inputs Analog Inputs COAXIAL:2 OPTICAL :2 DVD/BD, VCR/DVR, CBL/SAT, TV/TAPE, CD, AUX (PORTABLE) ■ Audio Outputs Analog Outputs Subwoofer Pre Output Speaker
  • Onkyo HT-R570 | Owner Manual - Page 89
    V/ 60 Hz Power consumption 163 W Other: Auto Standby function ■ Front Speaker (SKF-570) Type: 2 Way Bass-reflex Impedance: 6 Ω 1.0 kg (2.2 lbs.) Drivers unit: 8 cm (3-1/4") Cone Terminal: Spring type color coded Keyhole slot: 1 Grille: Fixed UP-A1L Dimensions (W × H × D): Weight:
  • Onkyo HT-R570 | Owner Manual - Page 90
    Memo 90
  • Onkyo HT-R570 | Owner Manual - Page 91
    Memo 91
  • Onkyo HT-R570 | Owner Manual - Page 92
    Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8163 ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/ ONKYO EUROPE ELECTRONICS GmbH
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
E
n
7.1ch Home Theater System
HT-S5200
AV Receiver (HT-R570)
Speaker Package (HTP-570)
Front Speakers (SKF-570 L/R)
Center Speaker (SKC-570)
Surround Speakers (SKR-570 L/R)
Surround Back Speakers (SKB-570 L/R)
Subwoofer (SKW-570)
Dock for iPod (UP-A1L)
Instruction Manual
Thank you for purchasing an Onkyo 7.1ch Home
Theater System. Please read this manual thoroughly
before making connections and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new 7.1ch Home Theater Sys-
tem.
Please retain this manual for future reference.
Contents
Introduction
...................................
2
Connections
................................
18
Turning On & First Time Setup
.....
38
Basic Operations
.........................
44
Using the Listening Modes
........
64
Advanced Setup
..........................
70
Controlling Other Components
....
78
Others
...........................................
84