Onkyo HT-R570 Owner Manual - Page 37

Connecting Onkyo u Components, Connecting the Power Cord, Auto Power On/Standby, Direct Change

Get Onkyo HT-R570 PDF manuals and user guides View all Onkyo HT-R570 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Connecting the AV receiver-Continued Connecting Onkyo V Components Step 1: Make sure that each Onkyo component is connected to the AV receiver with an analog audio cable (RCA). Step 2: Make the necessary V connections (see illustration below). Step 3: If you're using an MD, CDR, or RI DOCK component, change the Input Display (see page 43). With V (Remote Interactive), you can use the following special functions: ■ Auto Power On/Standby When you start playback on a component connected via V, if the AV receiver is on Standby, it will automatically turn on and select that component as the input source. Similarly, when the AV receiver is set to Standby, all components connected via V will also go on Standby. ■ Direct Change When playback is started on a component connected via V, the AV receiver automatically selects that component as the input source. ■ Remote Control You can use the AV receiver's remote controller to control your other V-capable Onkyo components. You must enter the appropriate remote control code first (see page 79). And remember to point the remote controller at the AV receiver and not the other component. Notes: • Use only V cables for V connections. V cables are supplied with Onkyo players (DVD, CD, etc.). • Some components have two V jacks. You can connect either one to the AV receiver. The other jack is for connecting additional V-capable components. • Connect only Onkyo components to V jacks. Connecting other manufacturer's components may cause a malfunction. • Some components may not support all V functions. Refer to the manuals supplied with your other Onkyo components. REMOTE CONTROL e.g., CD player e.g., DVD player IN L R CD IN L R DVD/BD R L ANALOG AUDIO OUT R L ANALOG AUDIO OUT Connecting the Power Cord Notes: • Before connecting the power cord, connect all your speakers and AV components. • Plug the end of the power cord into a suitable wall outlet. • Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
37
Connecting the AV receiver
—Continued
With
u
(Remote Interactive), you can use the following special functions:
■
Auto Power On/Standby
When you start playback on a component connected via
u
, if the AV receiver is on Standby, it will automatically
turn on and select that component as the input source. Similarly, when the AV receiver is set to Standby, all
components connected via
u
will also go on Standby.
■
Direct Change
When playback is started on a component connected via
u
, the AV receiver automatically selects that component
as the input source.
■
Remote Control
You can use the AV receiver’s remote controller to control your other
u
-capable Onkyo components. You must
enter the appropriate remote control code first (see page 79). And remember to point the remote controller at the AV
receiver and not the other component.
Notes:
•
Use only
u
cables for
u
connections.
u
cables
are supplied with Onkyo players (DVD, CD, etc.).
•
Some components have two
u
jacks. You can
connect either one to the AV receiver. The other jack
is for connecting additional
u
-capable
components.
•
Connect only Onkyo components to
u
jacks.
Connecting other manufacturer’s components may
cause a malfunction.
•
Some components may not support all
u
functions.
Refer to the manuals supplied with your other Onkyo
components.
Notes:
•
Before connecting the power cord, connect all your speakers and AV components.
•
Plug the end of the power cord into a suitable wall outlet.
•
Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical equipment
on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit.
Connecting Onkyo
u
Components
Step 1:
Make sure that each Onkyo component is connected to the AV receiver with an analog audio cable (RCA).
Step 2:
Make the necessary
u
connections (see illustration below).
Step 3:
If you’re using an MD, CDR, or RI DOCK component, change the Input Display (see page 43).
L
R
IN
DVD/BD
L
R
IN
CD
L
R
REMOTE
CONTROL
ANALOG
AUDIO OUT
L
R
ANALOG
AUDIO OUT
e.g., CD player
e.g., DVD player
Connecting the Power Cord