Onkyo TX-NR509 Owner Manual - Page 60
Video, About DTS signals - bundle
View all Onkyo TX-NR509 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 60 highlights
■ Only the front speakers produce sound When the Stereo or Mono listening mode is selected, 33 only the front speakers and subwoofer produce sound. Check the Speaker Configuration. 41 ■ Only the center speaker produces sound If you use the Dolby Pro Logic IIx Movie, Dolby Pro - Logic IIx Music, or Dolby Pro Logic IIx Game listening mode with a mono source, such as an AM radio station or mono TV program, the sound is concentrated in the center speaker. Make sure the speakers are configured correctly. 41 ■ The surround speakers produce no sound When the T-D (Theater-Dimensional), Stereo or - Mono listening mode is selected, the surround speakers produce no sound. Depending on the source and current listening mode, 31-32 not much sound may be produced by the surround speakers. Try selecting another listening mode. Make sure the speakers are configured correctly. 41 ■ The center speaker produces no sound When the Stereo or Mono listening mode is selected, 33 the center speaker produces no sound. Make sure the speakers are configured correctly. 41 ■ The surround back speakers produce no sound Depending on the current listening mode, no sound 31 may be produced by the surround back speakers. Select another listening mode. Not much sound may be produced by the surround - back speakers with some sources. Make sure the speakers are configured correctly. 41 ■ The subwoofer produces no sound When you play source material that contains no - information in the LFE channel, the subwoofer produces no sound. Make sure the speakers are configured correctly. 41 ■ There's no sound with a certain signal format Check the digital audio output setting on the - connected device. On some game consoles, such as those that support DVD, the default setting is off. With some DVD-Video discs, you need to select an - audio output format from a menu. Depending on the input signal, some listening modes 31-32 cannot be selected. ■ Can't select the Pure Audio listening mode (European, Australian and Asian models) The - Pure Audio listening mode cannot be selected while Zone 2 is on. ■ Can't get 6.1/7.1 playback If no surround back speakers are connected, 6.1/7.1 - playback is not possible. You can not always select all of the listening modes, 31-32 En depending on the number of the speakers connected. 60 ■ The speaker volume cannot be set as required Check to see if a maximum volume has been set. If the volume level of each individual speaker has been adjusted to high positive values, then the maximum master volume possible may be reduced. Note that the individual speaker volume levels are set automatically after the Audyssey 2EQ® Room Correction and Speaker Setup has been completed. 20 28, 42 ■ Noise can be heard Using cable ties to bundle audio cables with power - cords, speaker cables, and so on may degrade the audio performance, so don't do it. An audio cable may be picking up interference. Try - repositioning your cables. ■ The Late Night function doesn't work Make sure the source material is Dolby Digital, 51 Dolby Digital Plus, and Dolby TrueHD. ■ About DTS signals When DTS program material ends and the DTS - bitstream stops, the AV receiver remains in DTS listening mode and the DTS indicator remains on. This is to prevent noise when you use the pause, fast forward, or fast reverse function on your player. If you switch your player from DTS to PCM, because the AV receiver does not switch formats immediately, you may not hear any sound, in which case you should stop your player for about three seconds, and then resume playback. With some CD and LD players, you won't be able to - playback DTS material properly even though your player is connected to a digital input on the AV receiver. This is usually because the DTS bitstream has been processed (e.g., output level, sampling rate, or frequency response changed) and the AV receiver doesn't recognize it as a genuine DTS signal. In such cases, you may hear noise. Playing DTS program material, using the pause, fast - forward, or fast reverse function on your player may produce a short audible noise. This is not a malfunction. ■ The beginning of audio received by an HDMI IN can't be heard Since it takes longer to identify the format of an - HDMI signal than it does for other digital audio signals, audio output may not start immediately. Video ■ There's no picture Make sure that all video connecting plugs are pushed 14 in all the way. Make sure that each video component is properly 15, 16, connected. 17 If the video source is connected to a component video input, you must assign that input to an input selector, and your TV must be connected to COMPONENT VIDEO OUT. 16, 40 If the video source is connected to a composite video 16 input, your TV must be connected to the corresponding composite video output.