Onkyo TX-SR343 User Manual - Page 22

Details on AM/FM reception

Get Onkyo TX-SR343 PDF manuals and user guides View all Onkyo TX-SR343 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Details on AM/FM reception Tuning into a Radio Station „„Tuning Automatically 1. Press TUNER on the remote controller several times to select either "AM" or "FM". When the signal from an FM radio station is weak: Radio wave may be weak depending on the building structure and environmental conditions. In that case, perform the procedure as explained below in "Tuning Manually" to manually select the desired station. „„Tuning Manually 1. Press TUNER on the remote controller several times to select either "AM" or "FM". Details on AM/FM reception „„Directly inputting the frequency It allows you to directly enter the frequency of the radio station you want to listen to. 1. Press TUNER on the remote controller several times to select either "AM" or "FM". 2. Press D.TUN. 2. Press TUN MODE so that the "AUTO" indicator on the display lights. 3. Press the cursors / to start automatic tuning. ●● Alternatively you can press TUNING on the main unit to start tuning automatically. ●● Searching automatically stops when a station is found. When tuned into a radio station, the " TUNED " indicator on the display lights. When tuned into an FM radio station, the "FM STEREO" indicator lights. ●● No sound is output while the " TUNED " indicator is off. 2. Press TUN MODE so that the "AUTO" indicator on the display goes off. 3. While pressing the cursors / , select the desired radio station. ●● Alternatively you can press TUNING on the main unit. ●● The frequency changes by 1 step each time you press the button. The frequency changes continuously if the button is held down and stops when the button is released. Tune by looking at the display. 3. Using the number buttons, enter the frequency of the radio station within 8 seconds. ●● To enter 87.5 (FM), for example, press 8, 7, 5, or 8, 7, 5, 0. If you entered a wrong number, press D.TUN and enter a correct one. En-2 To return to automatic tuning: Press TUN MODE on the remote controller again. The unit tunes automatically into a radio station. Normally "AUTO" should be displayed.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Details on AM/FM reception
En-2
Details on AM/FM reception
Tuning into a Radio Station
Tuning Automatically
1. Press TUNER on the remote controller several times to
select either "AM" or "FM".
2. Press TUN MODE so that the "AUTO" indicator on the
display lights.
3. Press the cursors
/
to start automatic tuning.
●
Alternatively you can press
TUNING
on the main
unit to start tuning automatically.
●
Searching automatically stops when a station is
found. When tuned into a radio station, the
"
TUNED
" indicator on the display lights. When
tuned into an FM radio station, the "FM STEREO"
indicator lights.
●
No sound is output while the "
TUNED
" indicator
is off.
When the signal from an FM radio station is weak
:
Radio wave may be weak depending on the building
structure and environmental conditions. In that case,
perform the procedure as explained below in "Tuning
Manually" to manually select the desired station.
Tuning Manually
1. Press TUNER on the remote controller several times to
select either "AM" or "FM".
2. Press TUN MODE so that the "AUTO" indicator on the
display goes off.
3. While pressing the cursors
/
, select the desired radio
station.
●
Alternatively you can press
TUNING
on the main
unit.
●
The frequency changes by 1 step each time
you press the button. The frequency changes
continuously if the button is held down and stops
when the button is released. Tune by looking at the
display.
To return to automatic tuning
: Press TUN MODE on the
remote controller again. The unit tunes automatically into a
radio station. Normally "AUTO" should be displayed.
Directly inputting the frequency
It allows you to directly enter the frequency of the radio
station you want to listen to.
1. Press TUNER on the remote controller several times to
select either "AM" or "FM".
2. Press D.TUN.
3. Using the number buttons, enter the frequency of the
radio station within 8 seconds.
●
To enter 87.5 (FM), for example, press 8, 7, 5, or 8,
7, 5, 0. If you entered a wrong number, press D.TUN
and enter a correct one.