Panasonic KX-TGE445B Operating Manual - Page 37

Other programming, Registering a unit, Answering the baby monitor, Changing the handset name

Get Panasonic KX-TGE445B PDF manuals and user guides View all Panasonic KX-TGE445B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Programming Answering the baby monitor n When monitoring with a unit: Handset: Press M N to answer a call. Base unit: Press M N to answer a call*1. *1 KX-TGE440 series: page 3 If you want to respond from the monitoring unit, press MMUTEN. R The monitoring unit will answer calls automatically when the auto intercom feature is set to "On" (page 21). Note: R If you receive an outside call when communicating with the monitored handset, the interrupt tone sounds. - To answer the call with the handset, press MOFFN, then press M N. - To answer the call with the base unit, press MZN 3 times.*1 *1 If MMUTEN is pressed, press MZN 2 times. n When monitoring from outside: Answer the call. If you want to respond from your monitoring phone, press #1 using tone dialing. You can turn off the baby monitor feature by pressing #0. Note: R The unit disconnects the call automatically after 2 minutes. Other programming Changing the handset name The default handset name is "Handset 1" to "Handset 6". You can customize the name of each handset ("Bob", "Kitchen", etc.). This is useful when you make intercom calls between handsets. To display the handset name in standby mode, turn on the handset name display feature (page 37). 1 MMENUN#104 2 Enter the desired name (10 characters max.). a MSAVEN a MOFFN Displaying the handset name You can select whether or not the handset name is displayed in standby mode. The default setting is "Off". 1 MMENUN#105 2 MbN: Select the desired setting. a MSAVEN a MOFFN Registering a unit Operating additional units Additional handsets Up to 6 handsets can be registered to the base unit. Important: R See page 5 for information on the available model. Registering a handset to the base unit The supplied handset and base unit are pre-registered. If for some reason the handset is not registered to the base unit, re-register the handset. 1 Handset: MMENUN#130 2 Base unit: Press and hold MLOCATORN or MHANDSET LOCATORN for about 5 seconds. R If all registered handsets start ringing, press MLOCATORN or MHANDSET LOCATORN again to stop, then repeat this step. 3 Handset: Press MOKN, then wait until a long beep sounds. For assistance, please visit http://shop.panasonic.com/support 37 TGE43xUS(en)_1112_ver021.pdf 37 2015/11/12 10:12:57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Answering the baby monitor
n
When monitoring with a unit:
Handset:
Press
M
N
to answer a call.
Base unit:
Press
M
N
to answer a call
*1
.
*1
KX-TGE440 series: page 3
If you want to respond from the monitoring
unit, press
M
MUTE
N
.
R
The monitoring unit will answer calls
automatically when the auto intercom
feature is set to
“
On
”
(page 21).
Note:
R
If you receive an outside call when
communicating with the monitored handset,
the interrupt tone sounds.
–
To answer the call with the handset,
press
M
OFF
N
, then press
M
N
.
–
To answer the call with the base unit,
press
M
Z
N
3 times.
*1
*1
If
M
MUTE
N
is pressed, press
M
Z
N
2
times.
n
When monitoring from outside:
Answer the call.
If you want to respond from your monitoring
phone, press
#1
using tone dialing.
You can turn off the baby monitor feature
by pressing
#0
.
Note:
R
The unit disconnects the call automatically
after 2 minutes.
Other programming
Changing the handset name
The default handset name is
“
Handset 1
”
to
“
Handset 6
”
. You can customize the name
of each handset (“Bob”, “Kitchen”, etc.). This is
useful when you make intercom calls between
handsets. To display the handset name in
standby mode, turn on the handset name
display feature (page 37).
1
M
MENU
N#104
2
Enter the desired name (10 characters
max.).
a
M
SAVE
N
a
M
OFF
N
Displaying the handset name
You can select whether or not the handset
name is displayed in standby mode. The
default setting is
“
Off
”
.
1
M
MENU
N#105
2
M
b
N
: Select the desired setting.
a
M
SAVE
N
a
M
OFF
N
Registering a unit
Operating additional units
Additional handsets
Up to 6 handsets can be registered to the
base unit.
Important:
R
See page 5 for information on the available
model.
Registering a handset to the
base unit
The supplied handset and base unit are
pre-registered. If for some reason the handset
is not registered to the base unit, re-register
the handset.
1
Handset:
M
MENU
N#130
2
Base unit:
Press and hold
M
LOCATOR
N
or
M
HANDSET LOCATOR
N
for about 5
seconds.
R
If all registered handsets start ringing,
press
M
LOCATOR
N
or
M
HANDSET
LOCATOR
N
again to stop, then repeat
this step.
3
Handset:
Press
M
OK
N
, then wait until a long beep
sounds.
For assistance, please visit http://shop.panasonic.com/support
37
Programming
TGE43xUS(en)_1112_ver021.pdf
37
2015/11/12
10:12:57