Panasonic MJ-L500 Operating Manual - Page 10

EN18

EN19

English

Please check the following before contacting

us for repair.

Problem

Cause and solution

●

This is normal.

You may hear sound such as squeaking or cracking.

These are the sound of ingredients being compressed.

(Depending on the ingredients, the noise may be quite loud.)

This is the sound of the rotating brush contacting with filter.

Noise during operation.

●

The rubber, rubber brushes and/or rubber plug are not

assembled correctly.

➡

Assemble them correctly. (P. EN10,11,17)

Leakage of juice or

frozen dish.

●

The squeezing screw and attachments are not assembled correctly.

➡

Assemble the squeezing screw and attachments correctly (P. EN10,11).

Abnormal noise or

vibration.

The juicer does not

run after the power is

switched on.

●

Is the power plug inserted into an outlet?

➡

Insert the power plug into an outlet.

●

➡

The lid needs to be turned until you hear a “click” sound. If you

fail to do so, the juicer will not run after the power is switched

on. (P. EN12)

●

The overload protection is activated.

➡

See “Overload protection” (P. EN19).

Remove prohibited ingredients from the juicer.

The motor housing is hot.

●

The operating time is longer than the rated duration.

➡

Follow the rated duration (up to 15 minutes).

To resume operation, please wait for at least 30 minutes. This

allows the motor housing to cool down and avoid failure due to

overheating of motor.

The juicer stopped

suddenly.

●

The lid is open.

➡

Switch off the power, close the lid, and start again.

●

The overload protection is activated.

➡

See “Overload protection” (P. EN19).

Remove prohibited ingredients from the juicer.

●

Clogging of pulp spout.

➡

Switch off the power and remove residue using the tip of

the cleaning brush handle.

The juicing bowl or motor

housing shakes during

operation.

●

This is normal.

Since the juicing bowl and motor housing are split type, they

may shake when the squeezing screw is rotating.

Do not press the lid or juicing bowl. (Doing so may result in

failure of the juicer.)

Overload protection

The motor may stop running when the internal overload protection is activated to prevent overload of motor.

If the motor stops, please take the following steps:

3

2

●

If the squeezing screw fails to run after reverse operation, then it means overheat protection is

activated. In this case, please unplug the power plug and leave the juicer to cool down for at

least 30 minutes.

4

●

Reduce the amount of ingredients being fed in and push them gently into feeding tube.

Specifications

MJ-L500

Power supply

120 V

60 Hz

Power consumption

150 W

18.5 × 17.6 × 43.2 cm

(7.3 × 6.9 × 17.0 inches)

4.0 k

g

(8.8 lb)

1.0 m (39.4 inches)

Replacement Parts

1

ON

REVERSE

OFF

■

Filter

Part number:

AJD33-153-K0

■

Gasket

Part number:

AJD27-153

■

Frozen attachment

Part number:

AJD38-153-A0

■

Pulp container

Part number:

AJD36-153-K1

■

Rotating brush

Part number:

AJD35-153-K0

■

Rubber brush

Part number:

AJD34-153

■

Juice container

Part number:

AJD05-153-K1

●

Press the “O” (OFF) button.

Panasonic MJ-L500 Operating Manual - Page 10

Overload protection, Specifications, Replacement Parts

Page 10 highlights