Pfaff admire air 5000 Manual - Page 7

Connecting the Foot Control, and the Power Supply, Before Using Your Machine, for the First Time,

Get Pfaff admire air 5000 PDF manuals and user guides View all Pfaff admire air 5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Connecting the Foot Control and the Power Supply Foot control to use with this machine: Type C-1028 for USA/Canada, C-2085-1 for U.K., C-2065 for Australia, C-2060 for Continental Europe. Before plugging your machine in, make sure the voltage is the same as indicated on the lower rear side of the machine. Specifications vary from country to country. • Connect the foot control/electric power cord to the socket on the machine (A). • Plug the power cord plug into the electric outlet (B). • Push the power switch (C) to "I" to turn on the ma- chine. • Press the foot control to start sewing (D). Use the foot control to adjust the sewing speed. The harder you press, the faster the machine will sew. • To stop the machine from sewing, remove your foot from the control. • Push the power switch to "0" to turn off the machine. Note: When the front cover and/or the flat bed extension cover is/are opened, the safety switch is activated and prevents the machine from sewing, even if the foot control is pressed. The machine will also be prevented from sewing when the foot is raised. Note: Your overlock machine is adjusted to provide the best stitch result at normal room temperature. Extreme hot and cold temperatures can affect the sewn result. Before Using Your Machine for the First Time Before using your machine for the first time, place a scrap of fabric under the presser foot and run the machine without thread for a few minutes. Wipe away any oil which may appear. A B C D POLARIZED PLUG INFORMATION (FOR U.S.A. & CANADA ONLY) This appliance has a polarized plug (one blade wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the plug in any way. Setting Up the Telescopic Thread Stand Extend the telescopic thread stand to its full height, then turn until it clicks into place. If the machine is already threaded, straighten the threads to prevent tangling. ABOUT YOUR MACHINE - 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
A
B
C
D
ABOUT YOUR MACHINE – 7
POLARIZED PLUG INFORMATION
(FOR U.S.A. & CANADA ONLY)
This appliance has a polarized plug (one blade wider
than the other). To reduce the risk of electric shock,
this plug is intended to fit in a polarized outlet only
way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified elec
-
trician to install the proper outlet. Do not modify the
plug in any way.
Connecting the Foot Control
and the Power Supply
Foot control to use with this machine:
Type C-1028 for USA/Canada, C-2085-1 for U.K., C-2065 for
Australia, C-2060 for Continental Europe.
Before plugging your machine in, make sure the volt-
age is the same as indicated on the lower rear side of
the machine. Specifications vary from country to coun
-
try.
•
Connect the foot control/electric power cord to the
socket on the machine (A).
•
Plug the power cord plug into the electric outlet (B).
•
Push the power switch (C) to “I” to turn on the ma-
chine.
•
Press the foot control to start sewing (D). Use the foot
control to adjust the sewing speed. The harder you
press, the faster the machine will sew.
•
To stop the machine from sewing, remove your foot
from the control.
•
Push the power switch to “0” to turn off the machine.
Note: When the front cover and/or the flat bed extension cover
is/are opened, the safety switch is activated and prevents the
machine from sewing, even if the foot control is pressed. The
machine will also be prevented from sewing when the foot is
raised.
Note: Your overlock machine is adjusted to provide the best
stitch result at normal room temperature. Extreme hot and cold
temperatures can affect the sewn result.
Before Using Your Machine
for the First Time
Before using your machine for the first time, place a scrap
of fabric under the presser foot and run the machine
without thread for a few minutes. Wipe away any oil
which may appear.
Setting Up the Telescopic Thread Stand
Extend the telescopic thread stand to its full height, then
turn until it clicks into place.
If the machine is already threaded, straighten the threads
to prevent tangling.