Philips CD4453Q User manual - Page 39

Frequently asked, questions

Page 39 highlights

9 Frequently asked questions www.philips.com/support In this chapter you will find the most frequently asked questions and answers about your phone. Connection The is blinking. • Move closer to the base station • Check battery level • Register the handset to the base station The handset does not switch on! • Charge the battery : Put the handset on charger. After a few moments the phone will switch on. • Check the charger connections • Use only the SUPPLIED RECHARGEABLE BATTERIES The phone does not work at all. • Make sure that the adaptor and the phone cord are connected properly • Check that the batteries are fully charged and installed properly • This phone does not work during power failure Communication is lost during a call! • Charge the battery • Move closer to the base station Poor audio quality • Move closer to the base station • Move the base station at least one metre away from any electrical appliances No dialling tone • Check the connections. Reset the phone : unplug and plug back in the mains. • Charge the batteries for at least 24 hours • Move closer to the base station • Use the line cable provided • Connect the line adaptor (when needed) to the line cord The appears soon after the batteries are charged. • Replace the batteries with new ones (use only RECHARGEABLE batteries) Set-up Caller ID does not work properly. • Check with your local phone company that the CID service is subscribed to • Let the phone ring at least once before answering The Call Waiting call cannot be answered. • Check with your local phone company and select the correct recall duration The handset LCD displays nothing. • Try again by disconnecting and connecting the base station power supply and follow the procedure to register a handset (see Section 5.7.6) • Make sure the two supplied rechargeable batteries have been inserted properly into the battery compartment • Remove and place back the handset batteries • Make sure the supplied batteries are charged up The handset displays UNREGISTERED • Follow the procedures to register the handset to a base Frequently asked questions 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48

Frequently asked questions
37
9
Frequently asked
questions
www.philips.com/support
In this chapter you will find the most frequently
asked questions and answers about your phone.
Connection
The handset does not switch on!
Charge the battery : Put the handset on
charger.After a few moments the phone will
switch on.
Check the charger connections
Use only the
SUPPLIED
RECHARGEABLE BATTERIES
The phone does not work at all.
Make sure that the adaptor and the phone
cord are connected properly
Check that the batteries are fully charged
and installed properly
This phone does not work during power
failure
Communication is lost during a call!
Charge the battery
Move closer to the base station
Poor audio quality
Move closer to the base station
Move the base station at least one metre
away from any electrical appliances
No dialling tone
Check the connections. Reset the phone :
unplug and plug back in the mains.
Charge the batteries for at least 24 hours
Move closer to the base station
Use the line cable provided
Connect the line adaptor (when needed) to
the line cord
The
is blinking.
Move closer to the base station
Check battery level
Register the handset to the base station
The
appears soon after the batteries
are charged.
Replace the batteries with new ones (use
only
RECHARGEABLE
batteries)
Set-up
Caller ID does not work properly.
Check with your local phone company that
the CID service is subscribed to
Let the phone ring at least once before
answering
The Call Waiting call cannot be answered.
Check with your local phone company and
select the correct recall duration
The handset LCD displays nothing.
Try again by disconnecting and connecting
the base station power supply and follow
the procedure to register a handset (see
Section 5.7.6)
Make sure the two supplied rechargeable
batteries have been inserted properly into
the battery compartment
Remove and place back the handset
batteries
Make sure the supplied batteries are
charged up
The handset displays UNREGISTERED
Follow the procedures to register the
handset to a base