Pioneer HTP-710 Operating Instructions - Page 85

Problem, Remedy, During a playback search

Page 85 highlights

Additional information 10 English Français Deutsch Italiano Español Nederlands Problem Remedy Considerable noise in radio • Connect the antenna (page 42) and adjust the position for best reception. broadcasts. • Route any loose cables away from the antenna terminals and wires. • Fully extend the FM wire antenna, position for best reception, and secure to a wall (or connect an outdoor FM antenna). • Turn off equipment causing interference or move it away from the system (or move antennas farther away from equipment causing noise). Broadcast stations cannot • Connect an outdoor antenna (refer to page 42). be selected automatically. Noise during playback of a • Move the cassette deck away from your system, until the noise cassette deck. disappears. Sound is produced from • Set the SIGNAL SEL to HDMI, C1/O1/O2 (DIGITAL) or A (analog) other components, but not according to the type of connections made (refer to page 54). from LD or DVD player. • Set the digital input settings correctly (refer to page 54). • Make digital connections (refer to page 33) and set the SIGNAL SEL to C1/O1/O2 (DIGITAL) (refer to page 54). • Refer to the instruction manual supplied with the DVD player. No sound is output or a • Set the digital volume level of the player to full, or to the neutral position. noise is output when • Make sure the player's settings are correct and/or the DTS signal out is software with DTS is played on. Refer to the instruction manual supplied with the DVD player. back. • Set the input signal type to C1/O1/O2 (DIGITAL) (see Choosing the input signal on page 54). During a playback search, • This is not a malfunction, but be sure to turn the volume down to noise is output from a DTS prevent the output of loud noise from your speakers. compatible CD player. Everything seems to be set • Check that the positive/negative speaker terminals on the system are up correctly, but the matched with the corresponding terminals on the speakers (see page 16, playback sound is odd. 20 or 24). There seems to be a time lag • See Automatically setting up for surround sound (MCACC) on page 51 to between the speakers and set up your system again using MCACC (this will automatically the output of the subwoofer. compensate for a delay in the subwoofer output). Can't operate the remote control. • Replace the batteries (refer to page 50). • Operate within 7 m, 30° of the remote sensor (refer to page 50). • Remove the obstacle or operate from another position. • Avoid exposing the remote sensor on the front panel to direct light. The display is dark or off. • Press DIMMER on the control repeatedly to return to the default. 85 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272

Additional information
10
85
En
English
Deutsch
Italiano
Español
Français
Nederlands
Considerable noise in radio
broadcasts.
Connect the antenna (page 42) and adjust the position for best reception.
• Route any loose cables away from the antenna terminals and wires.
• Fully extend the FM wire antenna, position for best reception, and
secure to a wall (or connect an outdoor FM antenna).
• Turn off equipment causing interference or move it away from the
system (or move antennas farther away from equipment causing noise).
Broadcast stations cannot
be selected automatically.
• Connect an outdoor antenna (refer to page 42).
Noise during playback of a
cassette deck.
• Move the cassette deck away from your system, until the noise
disappears.
Sound is produced from
other components, but not
from LD or DVD player.
• Set the
SIGNAL SEL
to
HDMI
,
C1
/
O1
/
O2
(
DIGITAL
) or
A
(analog)
according to the type of connections made (refer to page 54).
• Set the digital input settings correctly (refer to page 54).
Make digital connections (refer to page 33) and set the
SIGNAL SEL
to
C1
/
O1
/
O2
(
DIGITAL
)
(refer to page 54).
• Refer to the instruction manual supplied with the DVD player.
No sound is output or a
noise is output when
software with DTS is played
back.
Set the digital volume level of the player to full, or to the neutral position.
• Make sure the player’s settings are correct and/or the DTS signal out is
on. Refer to the instruction manual supplied with the DVD player.
• Set the input signal type to
C1
/
O1
/
O2
(
DIGITAL
) (see
Choosing the
input signal
on page 54).
During a playback search,
noise is output from a DTS
compatible CD player.
• This is not a malfunction, but be sure to turn the volume down to
prevent the output of loud noise from your speakers.
Everything seems to be set
up correctly, but the
playback sound is odd.
• Check that the positive/negative speaker terminals on the system are
matched with the corresponding terminals on the speakers (see page 16,
20 or 24).
There seems to be a time lag
between the speakers and
the output of the subwoofer.
• See
Automatically setting up for surround sound (MCACC)
on page 51 to
set up your system again using MCACC (this will automatically
compensate for a delay in the subwoofer output).
Can’t operate the remote
control.
• Replace the batteries (refer to page 50).
• Operate within 7 m, 30
°
of the remote sensor (refer to page 50).
• Remove the obstacle or operate from another position.
• Avoid exposing the remote sensor on the front panel to direct light.
The display is dark or off.
• Press
DIMMER
on the control repeatedly to return to the default.
Problem
Remedy